AbuseMark Amaze Rev.3 AfroMini 32
Mini Naze32 Flight Controller/FC
**OPTIONAL 90 Degree Pin connector**
- 33mm x 16.5mm
- 1.75 gram without headers
- STM32F103CBT6 32-bit Cortex M3 processor
- MPU6050 Accelerometer/Gyro
- BMP085 Barometer (rev0)
- BMP180 Barometer (rev1)
- BMP280 Barometer (rev3)
- Only supports PPM RC Input
- 1 throttle, 4 servo outputs (for airplane mode)
- 4 motor outputs for quadrotor mode (rev0)
- 6 motor outputs for multirotor mode (rev1, rev3)
- 2 3.3V analog inputs (for pitot etc in airplane mode, rev0)
- Battery voltage monitor (rev3)
- Futaba s.bus inverter built in (rev3)
- Buzzer output (rev3)
- Additional UART pads for GPS/Spektrum
- Currently shipping version can be powered with up to 16V
Requires USB>3.3V serial cable (not included)Currently shipping rev3 BLACK 0.8mm thin boards. Note:
Hardware cannot be used with any DJI frames. This includes: FlameWheel
330, 450, 550, or any future or past frames released by DJI.
Note:
Using hardware with anything other than supplied "baseflight" firmware
will immediately make the end user ineligible for any kind of support or
warranty.
RotorX RX1105 Brushless Micro Motor
**4 Included**
The tiny RX1105 "Gatling" motors are quite simply in a class of their own in regards to performance, size and durability. Now on to their 5th generation, these super efficient powerhouses are capable of generating 110grams of thrust at 2.9A on a 3S powertrain. Weighing in at only a fraction over 5 grams total including motor wires, these motors also come with an optional T-style propeller mounting system that is designed to work with our upcoming RX3020 props to make 4S power feasible, but also with any other propeller that utilizes a 1.5mm shaft. Our frame mounting configuration will be made available to purchasers, meaning you can design your own frames to take advantage of these little beasts. Perhaps most importantly, these micro motors are designed to survive even the hardest of crashes, allowing you to stay in the air longer and have less replacement costs.
Specifications:
- Lipo Range: 1~3S (3.7~11.7V) with 4S operation in testing stage
- Suggested prop: RX3020
- Max current: TBA
- Burst current (10sec): TBA
- Weight: 5.1g (including mount and wire)
- Shaft: 1.5mm
- Shaft length: 4mm
- Dimensions : 13 x 10mm
Test Data:
- 3020 prop (2g outrunner)
- Voltage: 12.3V
- Current: 2.9A
- Thrust: 110g
RotorX RX3020 T-Motor Style 3" White Propeller
**1 Package Included**
**In Stock Now Shipping**
Motors that were designed and made for these Props:
RotorX RX3020 T-Motor Style 3" Black Propellers
**1 Package Included**
Set of 6 RX3020 custom made propellers with a T-style mounting system for attaching to RX1104 motors only. Requires 2x M2 6mm screws for mounting per motor.
Motors that were designed and made for these Props:
FVT Little Bee Opto OneShot125 BLHeli 20a ESC
**Comes with 4 ESCs**
Latest Blheli firmware 14 (14.0.0.3) Download link
Silabs Chip
Oneshot / Active Braking (dampened light mode)
Signal wire programmable with an Arduino board Link as these have the blheli bootloader the afro toolstick and rctimer linker will not work
Input: 2-4s Lipo
Constant: 20 Amps
Burst: 30 Amps
Weight: 4g bare board
Dimensions: 23x12.5x3mm
Motor wire: 70mm
Signal wire: 120mm
PCB - 4 Layer Blind Pole PCB - 3oz Pour
Mosfet: N-Channel
BEC: None "Opto"
With all Esc's that have active braking we recomend you isolate or filter all sensitive electronics to prevent feedback / spikes
The LSPDB is a great choice as it also has 12v & 5v outputs and are isolated with an Lc Filter
