A single frame piece of Carbon Fiber 3K twill 2.5mm thick
pure carbon fiber frame which, at this scale, offers a near invincible
backbone from which to build.
RotorX RX1306 High Performance 4100kv Brushless Motor
(Comes with six motors)
Motors are manufactured by Rc Tiger motors to RotorX specs. They are NOT rebranded motors that RotorX just put their name on.
These motors were designed and tested for use with RX3040T Tri-blade propellers.
- High Kv, so you only require 3s batteries for high performance
- Designed to RotorX's strict quality and crashability standards
- Mounting hardware included.
- Connectors and wire length designed for use with RXM20A ESCs
RotorX RX20a 20 Amp ESC w/Matching Bullet
Connectors for RX1105/RX1306 RotorX Motor
(comes with 6 ESCs)
Below Pic shows the white shrink wrap stripped off
for weight savings, along with OPTIONAL RotorX Brushless MotorEsc's were designed and programmed to run best on RotorX motors but can be used with any motor not drawing over 20 amps.
They also come with matching bullet connectors to match RX1105/RX1306 motors.
Makes for a much easier and faster build with minimal weight added
RotorX RX3040T Orange 3" Tri-Blade Propellers - 2CW x 2CCW

RotorX RX3040T ‘bigboys’ - 2CW x 2CCW
Following on from the success of the RX1104 motor and RX3020 propeller
combo, RotorX has designed a new 3” triblade 3040 propeller specifically
for use with 1306 brushless motors. These propellers provide explosive
power to micro FPV racers, like the RotorX RX122 Atom and RX155 Raiju.
Upwards of 320g thrust can be achieved per motor depending on your kv
and voltage, has proven to work well with 3S/4S 3100kv.
RotorX RX3040T White 3" Tri-Blade Propellers - 2CW x 2CCW

RotorX RX3040T ‘bigboys’ - 2CW x 2CCW
Following on from the success of the RX1104 motor and RX3020 propeller
combo, RotorX has designed a new 3” triblade 3040 propeller specifically
for use with 1306 brushless motors. These propellers provide explosive
power to micro FPV racers, like the RotorX RX122 Atom and RX155 Raiju.
Upwards of 320g thrust can be achieved per motor depending on your kv
and voltage, has proven to work well with 3S/4S 3100kv.
Get em' while they are hot!
NAZE 32 ACRO 6DF REV 5 Flight Controller Board
with Pins and Breakout Cable
PLEASE
NOTE: Includes Straight and Angled Pins and breakout cable as pictured.
Can be configured with BaseFlight or CleanFlight software.Designed
for use with small indoor or small to mid-sized outdoor multirotor
crafts, or as a standalone camera stabilizer. The Naze32 flight
controller is extremely simple to setup, with configuration based on the
familiar “MultiWii” software.
Features:Battery voltage monitoring
Built-in FrSky telemetry converter
Modern 32-bit processor (STM32 F103) running at 3.3V/72MHz.
Onboard USB for setup and configuration
Extra bright LEDs
Modern GUI for all operating systems, Base flight Configuration
Specifications:Height: 3.6cm
Width: 3.6cm
Weight: 6g (no headers, 8 grams with)
Sensors: MPU6050
Headers:
Includes 1x 3x6 90 degree pin headers, 1x 1x2 straight pin headers, 1x
2x3 90 degree pin headers, and 1x 2x5 straight pin headers.
Package Includes:Naze32 6DF Flight Controller
Angled Pins
Straight Pins
Breakout Cable
Click below to view the Matching RotorX Raiju (RX155) Carbon Fiber Canopy


