MICRO MinimOSD Minim OSD Mini OSD W/ KV Team
MOD For Naze32 Flight Controller
The Micro MinimOSD with all the features of the very popuar WiteSpy KV Team modded OSD but in a 16x16mm size.
Doesn't have the DC/DC converter, this means less heat when powered off a flight controller.
The
Micro MinimOSD is the same as the older MinimOSD hardware, but has been
modified to take advantage of custom firmware options.
You
can choose firmware that is MAVLink compatible for ArduCopter, or
MultiWii Serial compatible for MultiWii and Baseflight / Cleanflight
control boards.
You
can connect two batteries up to 4S so you can see the main flight
battery voltage. the second port will allow your FPV battery voltage on
the display as well.
Description:
NO DC/DC converter, power board via 5 volts
FTDI cable compatible pinout
Standard 6-pin ISP header
Two LED indicators
ATmega328P with Arduino bootloader
MAX7456 monochrome on-screen display
16 x 16mm Size
Pad for an Analog or Digital PWM RSSI signal
Pad for the connection of a Current Sensor
ATmega328P with Arduino bootloader
Standalone, or with APM / Flip / Flip32+ flight controllers
These modifications allow direct connection of two batteries (up to 4S)
This hardware take the hardware mods for this firmware, and builds them into an RTF solution.
This Board can be used just as a normal OSD for APM or it can be used with MWC KV Team Mod.
Two independent power sections with an LED indicator on each.
Solder jumpers for combining the power sections
Solder jumper for PAL video option
+5V 500mA regulator for up to +12V supply input
Exposed test points for HSYNC and LOS
Package included:
1 x Micro Minim OSD board
2 x pins (sets)
Abusemark FunFly Controller NAZE32 Acro
Version Flight Controller Rev6

Mini Flight Controller ???32? (pronounced "NAZE32").
This version is same as http://abusemark.com/store/index.php?main_page=product_info&cPath=1&products_id=30
except that the only sensor is MPU6500 acc + gyro. Acro version comes with BMP280 low-resolution barometer, but no compass.
STM32F103CBT6 32-bit ARM Cortex M3 processor (72MHz, 3.3V)
Invensense MPU6500 MEMS accelerometer + gyro
BMP280 low-resolution baro for altitude logging, etc
Built-in Micro-USB for programming/firmware update
36x36mm size, ~5 gram weight w/o headers
Made in JAPAN
Since 08/10/2014, these are shipping with 16V input capable voltage regulators
These
come with all needed headers, NOT soldered to the board. RC input
breakout cable is included if selected below, to allow connecting to
4channel+ receiver.
Included:
1x AcroNaze32 rev6
1x right angle header
1x RC breakout cable (if selected)Configuration software - Chrome Baseflight Configurator (preferred)
https://chrome.google.com/webstore/detail/baseflight-configurator/mppkgnedeapfejgfimkdoninnofofigkNote:
Currently shipping rev6 boards in random colors. Hardware
specifications and layout are subject to change without notice for
improvement. Letter revisions (i.e. REV6A,B,C, etc) are for correcting
non-critical issues or manufacturing optimizations.
Note: This
hardware cannot be used with any DJI frames. This includes: FlameWheel
330, 450, 550, or any future or past frames released by DJI.
Note:
Using this hardware with anything other than supplied "baseflight"
firmware will immediately make the end user ineligible for any kind of
support or warranty.
Phoenix Flight Gear RotorX Atom Foam Case(s):
