Home > Multi Rotor Kits (RTF/ARF) > RotorX

RotorX RX122 Atom Mini Quadcopter FPV RX1306 ARF Kit

Item Id: ROT-RX122RX122

Your Price:

$286.00

Availability:

In Stock

Choose Options

Naze32 Flight Controller Breakout Cable

FVT USB Programmer For Little Bee ESC's

Quantity

Email a friend

Description

RotorX RX122 Atom Mini Quadcopter

RX1306 FPV ARF Kit #2

Included with this kit...

RotorX RX122 Atom 122mm Mini Quad Carbon Fiber Frame

(Comes WITH Accessory Top Plate)

A two piece frame Carbon Fiber 3K micro quadcopter which, at this scale, offers a near invincible backbone from which to build.

The frame plate is 2.5mm carbon fiber and the top plate is 1.5mm carbon fiber

Included

Atom hardware bag
Atom Top Accessory Plate

RotorX Atom Lightweight Micro/Mini Power Distribution Board (PDB)

Want to simplify your install and keep your build nice and clean?

We have the solution!

The RotorX Atom PDB Board.

It was designed for the RotorX Atom but will work on just about any small brushless build.

Weighs in at only 2g and has connection points for 4-ESC's, LED's, Polulu reg, Micro MinimOSD, RX, and more.

Build Guide

RotorX RX1306 High Performance 4100kv Brushless Motor

(4 MOTORS INCLUDED)

Motors are manufactured by Rc Tiger motors to RotorX specs.

They are NOT rebranded motors that RotorX just put their name on

These motors were designed and tested for use with RX3040T Tri-blade propellers.

High Kv, so you only require 3s batteries for high performance
Designed to RotorX's strict quality and crashability standards
Mounting hardware included.
Connectors and wire length designed for use with RXM20A ESCs

RotorX RX3040T White 3" Tri-Blade Propellers - 2CW x 2CCW

RotorX RX3040T ‘bigboys’ - 2CW x 2CCW

Following on from the success of the RX1104 motor and RX3020 propeller combo, RotorX has designed a new 3” triblade 3040 propeller specifically for use with 1306 brushless motors. These propellers provide explosive power to micro FPV racers, like the RotorX RX122 Atom and RX155 Raiju. Upwards of 320g thrust can be achieved per motor depending on your kv and voltage, has proven to work well with 3S/4S 3100kv.

RotorX RX3040T Orange 3" Tri-Blade Propellers - 2CW x 2CCW

RotorX RX3040T ‘bigboys’ - 2CW x 2CCW

RotorX RX20a 20 Amp ESC w/Matching Bullet

Connectors for RX1105/RX1306 RotorX Motor

Comes with 4 ESCs

Below Pic shows the white shrink wrap stripped off
for weight savings, along with OPTIONAL RotorX Brushless Motor

Esc's were designed and programmed to run best on RotorX motors but can be used with any motor not drawing over 20 amps.
They also come with matching bullet connectors to match RX1105/RX1306 motors.
Makes for a much easier and faster build with minimal weight added

600TVL 1/4 1.8mm CMOS FPV 170 Degree Wide

Angle Lens Camera NTSC

Description:

Resolution: 1280 * 960
Resolution: 600TVL
Camera Dimensions: 12.5mm * 12.5mm * 17mm
Illumination: 0.5LUX
Format:PAL / NTSC
Power supply range: 3.7-5V 100mA
Audio Lens: Wide-angle 1.8mm (170 degree)
Image sensor:1/4 CMOS image sensor
Sensitive area: 3.5964mm x 2.7084mm
648 pixels (horizontal) × 488 (vertical) 648 (horizontal) × 488 (vertical)
Scanning Frequency Horizontal: 15.625KHz
Vertical: 50Hz
level: 15.7343KHz
Vertical: 60Hz
Electronic Shutter 1 / 50-1 / 80000 (sec) 1 / 60-1 / 80000 (sec)
SNR =48dB (AGC OFF)
Minimum illumination : 0.1 Lux / F1.2
Composite video signal :1.0Vp-p 75O
Standard Lens :1.8 mm
Specifications PCB: 20mm*20mm
Power: DC5V ± 10% 70mA ± 10%
Operating temperature :-10 ? ~ 60 ? RH95% Max

Note:It's only support 3.7-5V voltage , the manual book 5-12V voltage is wrong .

Package included:

1 x 600TVL Wide Angle Lens Camera

MICRO MinimOSD Minim OSD Mini OSD W/ KV Team

MOD For Naze32 Flight Controller

The Micro MinimOSD with all the features of the very popuar WiteSpy KV Team modded OSD but in a 16x16mm size.

Doesn't have the DC/DC converter, this means less heat when powered off a flight controller.

The Micro MinimOSD is the same as the older MinimOSD hardware, but has been modified to take advantage of custom firmware options.

You can choose firmware that is MAVLink compatible for ArduCopter, or MultiWii Serial compatible for MultiWii and Baseflight / Cleanflight control boards.

You can connect two batteries up to 4S so you can see the main flight battery voltage. the second port will allow your FPV battery voltage on the display as well.

Description:

NO DC/DC converter, power board via 5 volts

FTDI cable compatible pinout

Standard 6-pin ISP header

Two LED indicators

ATmega328P with Arduino bootloader

MAX7456 monochrome on-screen display

16 x 16mm Size

Pad for an Analog or Digital PWM RSSI signal

Pad for the connection of a Current Sensor

ATmega328P with Arduino bootloader

Standalone, or with APM / Flip / Flip32+ flight controllers

These modifications allow direct connection of two batteries (up to 4S)

This hardware take the hardware mods for this firmware, and builds them into an RTF solution.

This Board can be used just as a normal OSD for APM or it can be used with MWC KV Team Mod.

Two independent power sections with an LED indicator on each.

Solder jumpers for combining the power sections

Solder jumper for PAL video option

+5V 500mA regulator for up to +12V supply input

Exposed test points for HSYNC and LOS

Package included:

1 x Micro Minim OSD board

2 x pins (sets)

FX758-2 FPV 5.8G 200mW 32CH Wireless Audio Video AV Transmitter Module

Description:

Factory number: FXT758-2

Voltage: 5V

Power: 200mW

Frequency: 5725MHz-5945MHz

Size:22x19 mm

Modulation type: FM

Working temperature: -10?- +60?

Transmission frequency group:

A: Ch1:5725MHz Ch2:5745MHz Ch3:5765MHz Ch4:5785MHz

Ch5:5805MHz Ch6:5825MHz Ch7:5845MHz Ch8:5865MHz

B: Ch1:5733MHz Ch2:5752MHz Ch3:5771MHz Ch4:5790MHz

Ch5:5809MHz Ch6:5828MHz Ch7:5847MHz Ch8:5866MHz

C: Ch1:5645MHz Ch2:5665MHz Ch3:5685MHz Ch4:5705MHz

Ch5:5885MHz Ch6:5905MHz Ch7:5925MHz Ch8:5945MHz

Package Included:

1 x Transmitter Module FX758-2

Abusemark FunFly Controller NAZE32 Acro

Version Flight Controller Rev6

Mini Flight Controller ???32? (pronounced "NAZE32").
This version is same as http://abusemark.com/store/index.php?main_page=product_info&cPath=1&products_id=30
except that the only sensor is MPU6500 acc + gyro. Acro version comes with BMP280 low-resolution barometer, but no compass.

    STM32F103CBT6 32-bit ARM Cortex M3 processor (72MHz, 3.3V)
    Invensense MPU6500 MEMS accelerometer + gyro
    BMP280 low-resolution baro for altitude logging, etc
    Built-in Micro-USB for programming/firmware update
    36x36mm size, ~5 gram weight w/o headers
    Made in JAPAN
    Since 08/10/2014, these are shipping with 16V input capable voltage regulators

These come with all needed headers, NOT soldered to the board. RC input breakout cable is included if selected below, to allow connecting to 4channel+ receiver.

Included:
1x AcroNaze32 rev6
1x right angle header
1x RC breakout cable (if selected)

Configuration software - Chrome Baseflight Configurator (preferred)
https://chrome.google.com/webstore/detail/baseflight-configurator/mppkgnedeapfejgfimkdoninnofofigk

Note: Currently shipping rev6 boards in random colors. Hardware specifications and layout are subject to change without notice for improvement. Letter revisions (i.e. REV6A,B,C, etc) are for correcting non-critical issues or manufacturing optimizations.

Note: This hardware cannot be used with any DJI frames. This includes: FlameWheel 330, 450, 550, or any future or past frames released by DJI.

Note: Using this hardware with anything other than supplied "baseflight" firmware will immediately make the end user ineligible for any kind of support or warranty.

5.8gHz Right Hand/RH Micro CL/Cloverleaf

Lightweight Video Transmitter/VTX Antenna

Description:
Item Name:Micro CL Antenna
Anternna:TX Antenna
Frequency : 5.8 GHz
Weight : 3g(With Wires)

Package Included:
1x TX Antenna

Phoenix Flight Gear RotorX Atom Foam Case(s):

Browse Similar Items
RotorX Atom RX122 V1/V2/V3