RotorX Atom Lightweight Micro/Mini Power Distribution Board (PDB)
Want to simplify your install and keep your build nice and clean?
We have the solution!
The RotorX Atom PDB Board.
It was designed for the RotorX Atom but will work on just about any small brushless build.
Weighs in at only 2g and has connection points for 4-ESC's, LED's, Polulu reg, Micro MinimOSD, RX, and more.
RotorX RX1105 Gatling High Performance 4000kv Brushless Motor
(Includes FOUR MOTORS)
The tiny RX1105 "Gatling" motors are quite simply in a class of their own in regards to performance, size and durability.
Now on to their 6th generation, these super efficient powerhouses are capable of generating massive amounts of thrust.
We
worked with Alex Greves aka 'IBCrazy' to optimize this next generation
of motors to give the maximum thrust with our RX3020 props and some new
to be released props... There is no motor at this size that out performs
these powerhouses!
Our frame mounting configuration will be made
available to purchasers, meaning you can design your own frames to take
advantage of these little beasts.
Perhaps most importantly,
these micro motors are designed to survive even the hardest of crashes,
allowing you to stay in the air longer and have less replacement costs.
- Includes mounting hardware
- Small bullet connectors for easy mounting to RXM20A Esc.
RotorX RX3020 T-Motor Style 3" White Propeller
**1 Package Included**
**In Stock Now Shipping**
Motors that were designed and made for these Props:
RotorX RX3020 T-Motor Style 3" Black Propellers
**1 Package Included**
Set of 6 RX3020 custom made propellers with a T-style mounting system for attaching to RX1104 motors only. Requires 2x M2 6mm screws for mounting per motor.
Motors that were designed and made for these Props:
FVT Little Bee Opto OneShot125 BLHeli 20a ESC
**Comes with 4 ESCs**
Latest Blheli firmware 14 (14.0.0.3) Download link
Silabs Chip
Oneshot / Active Braking (dampened light mode)
Signal wire programmable with an Arduino board Link as these have the blheli bootloader the afro toolstick and rctimer linker will not work
Input: 2-4s Lipo
Constant: 20 Amps
Burst: 30 Amps
Weight: 4g bare board
Dimensions: 23x12.5x3mm
Motor wire: 70mm
Signal wire: 120mm
PCB - 4 Layer Blind Pole PCB - 3oz Pour
Mosfet: N-Channel
BEC: None "Opto"
With all Esc's that have active braking we recomend you isolate or filter all sensitive electronics to prevent feedback / spikes
The LSPDB is a great choice as it also has 12v & 5v outputs and are isolated with an Lc Filter
Hyperion 5.8GHZ CloverLeaf TX/RX Antenna set
(RP-SMA CONN)
These Antennas are a great way to improve the performance of your FPV
system. These are Right-Hand Circular Polarized Antenna (RHCP) which
helps reject "multipath interference”, this is a problem that plagues
the standard dipole stock antenna's.
This style of Antenna has
been proven to increase range and the video clarity and has become the
standard aftermarket upgrade for most FPV systems. These antenna have 3
lobes for the transmitter and 4 lobes for the receiver, they are encased
in a smart 2 piece plastic molded mushroom shaped housing.With the
included 90 degree adapters you can mount your Antennas from your VTX or
VRX either flat or upright.
Specifications: Frequency Range: 5725~5875GHz
Impedence: 50 ohm
VSWR: less than 1.5
Gain: 7db
Connector: RP-SMA with Flat or 90degree adapter
Lobes: 4 Receiver, 3 Transmitter
Polarization: Right-hand (RHCP)
Eachine 700tvl ET200 5.8G 32CH 200mW Mini Video Transmitter(VTX)
Brand Name : Eachine
Item Name : Transmitter
Item NO.: ET200
Modulation : Broadband FM
Support Video Format : NTSC/PAL
Output Impedance : 75 Ohm
Output Signal : 23~24dBm
Output Power : 200mW
Wireless Channels : 32CH
Working Voltage : 3.6V-5.5V
Current : 190mA
Audio Carrier : 6.5MHz
Antenna Connector : RP-SMA
Dimention : 38mm x 22.5mm x 6mm
Weight : 6g(without antenna) 15g (with antenna)
Frequency:
Band A : 5865,5845,5825,5805,5785,5765,5745,5725
Band B : 5733,5752,5771,5790,5809,5828,5847,5866
Band E : 5705,5685,5665,5645,5885,5905,5925,5945
Band F : 5740,5760,5780,5800,5820,5840,5860,5880
Package Included:
1 x Transmitter
1 x Antenna
1 x FPV Power Cable
1 x 5Pin Cable
600TVL 1/4 1.8mm CMOS FPV 170 Degree Wide
Angle Lens Camera NTSC
Description:
Resolution: 1280 * 960
Resolution: 600TVL
Camera Dimensions: 12.5mm * 12.5mm * 17mm
Illumination: 0.5LUX
Format:PAL / NTSC
Power supply range: 3.7-5V 100mA
Audio Lens: Wide-angle 1.8mm (170 degree)
Image sensor:1/4 CMOS image sensor
Sensitive area: 3.5964mm x 2.7084mm
648 pixels (horizontal) × 488 (vertical) 648 (horizontal) × 488 (vertical)
Scanning Frequency Horizontal: 15.625KHz
Vertical: 50Hz
level: 15.7343KHz
Vertical: 60Hz
Electronic Shutter 1 / 50-1 / 80000 (sec) 1 / 60-1 / 80000 (sec)
SNR =48dB (AGC OFF)
Minimum illumination : 0.1 Lux / F1.2
Composite video signal :1.0Vp-p 75O
Standard Lens :1.8 mm
Specifications PCB: 20mm*20mm
Power: DC5V ± 10% 70mA ± 10%
Operating temperature :-10 ? ~ 60 ? RH95% Max
Note:It's only support 3.7-5V voltage , the manual book 5-12V voltage is wrong .
Package included:
1 x 600TVL Wide Angle Lens Camera
MICRO MinimOSD Minim OSD Mini OSD W/ KV Team MOD For Naze32 Flight Controller
The Micro MinimOSD with all the features of the very popuar WiteSpy KV Team modded OSD but in a 16x16mm size.
Doesn't have the DC/DC converter, this means less heat when powered off a flight controller.
The
Micro MinimOSD is the same as the older MinimOSD hardware, but has been
modified to take advantage of custom firmware options.
You
can choose firmware that is MAVLink compatible for ArduCopter, or
MultiWii Serial compatible for MultiWii and Baseflight / Cleanflight
control boards.
You
can connect two batteries up to 4S so you can see the main flight
battery voltage. the second port will allow your FPV battery voltage on
the display as well.
Description:
NO DC/DC converter, power board via 5 volts
FTDI cable compatible pinout
Standard 6-pin ISP header
Two LED indicators
ATmega328P with Arduino bootloader
MAX7456 monochrome on-screen display
16 x 16mm Size
Pad for an Analog or Digital PWM RSSI signal
Pad for the connection of a Current Sensor
ATmega328P with Arduino bootloader
Standalone, or with APM / Flip / Flip32+ flight controllers
These modifications allow direct connection of two batteries (up to 4S)
This hardware take the hardware mods for this firmware, and builds them into an RTF solution.
This Board can be used just as a normal OSD for APM or it can be used with MWC KV Team Mod.
Two independent power sections with an LED indicator on each.
Solder jumpers for combining the power sections
Solder jumper for PAL video option
+5V 500mA regulator for up to +12V supply input
Exposed test points for HSYNC and LOS
Package included:
1 x Micro Minim OSD board
2 x pins (sets)
NAZE 32 ACRO 6DF REV 5 Flight Controller Board
with Pins and Breakout Cable
PLEASE
NOTE: Includes Straight and Angled Pins and breakout cable as pictured.
Can be configured with BaseFlight or CleanFlight software.
Designed
for use with small indoor or small to mid-sized outdoor multirotor
crafts, or as a standalone camera stabilizer. The Naze32 flight
controller is extremely simple to setup, with configuration based on the
familiar “MultiWii” software.
Features:
Battery voltage monitoring
Built-in FrSky telemetry converter
Modern 32-bit processor (STM32 F103) running at 3.3V/72MHz.
Onboard USB for setup and configuration
Extra bright LEDs
Modern GUI for all operating systems, Base flight Configuration
Specifications:
Height: 3.6cm
Width: 3.6cm
Weight: 6g (no headers, 8 grams with)
Sensors: MPU6050
Headers:
Includes 1x 3x6 90 degree pin headers, 1x 1x2 straight pin headers, 1x
2x3 90 degree pin headers, and 1x 2x5 straight pin headers.
Package Includes:
Naze32 6DF Flight Controller
Angled Pins
Straight Pins
Breakout Cable
Phoenix Flight Gear RotorX Atom Foam Case(s):
