AbuseMark Amaze Rev.3 AfroMini 32
Mini Naze32 Flight Controller/FC

**OPTIONAL 90 Degree Pin connector**

- 33mm x 16.5mm
- 1.75 gram without headers
- STM32F103CBT6 32-bit Cortex M3 processor
- MPU6050 Accelerometer/Gyro
- BMP085 Barometer (rev0)
- BMP180 Barometer (rev1)
- BMP280 Barometer (rev3)
- Only supports PPM RC Input
- 1 throttle, 4 servo outputs (for airplane mode)
- 4 motor outputs for quadrotor mode (rev0)
- 6 motor outputs for multirotor mode (rev1, rev3)
- 2 3.3V analog inputs (for pitot etc in airplane mode, rev0)
- Battery voltage monitor (rev3)
- Futaba s.bus inverter built in (rev3)
- Buzzer output (rev3)
- Additional UART pads for GPS/Spektrum
- Currently shipping version can be powered with up to 16V
Requires USB>3.3V serial cable (not included)Currently shipping rev3 BLACK 0.8mm thin boards. Note:
Hardware cannot be used with any DJI frames. This includes: FlameWheel
330, 450, 550, or any future or past frames released by DJI.
Note:
Using hardware with anything other than supplied "baseflight" firmware
will immediately make the end user ineligible for any kind of support or
warranty.
RotorX RX1105B/1105B 6500kv Brushless Motor
This new 1105 6500kv version is wound for a higher kv for a 2s or light 3s setup.
The new improved 1105 motors now come with NSK bearings for 20% more thrust and an even smoother running motor
The tiny RX1105 "Gatling" motors are quite simply in a class of their own in regards to performance, size and durability.
Now on to their 6th generation, these super efficient powerhouses are capable of generating massive amounts of thrust.
We
worked with Alex Greves aka 'IBCrazy' to optimize this next generation
of motors to give the maximum thrust with our RX3020 props and some new
to be released props... There is no motor at this size that out performs
these powerhouses!
Our
frame mounting configuration will be made available to purchasers,
meaning you can design your own frames to take advantage of these little
beasts.
Perhaps
most importantly, these micro motors are designed to survive even the
hardest of crashes, allowing you to stay in the air longer and have less
replacement costs.
- Includes mounting hardware
**Please help support RotorX by buying original RotorX products and not cheap clones**
RotorX is a company who cares about the end user and dealers that support them.
I have yet to work with ANY company that stands behind their product and puts the customer before profit like RotorX.
Hubsan Style 3-Blade Micro Props for
the DP03 Brushless Motors (8 Props Total)
Props will need to be drilled out to 1.5mm or you can add drilling service from the drop down box
DYS XM10A Mini ESC w/BLheli firmware for
High KV Motor for Mini Multirotors

DYS
XM10A Mini ESC is specially designed for the micro motor with high KV
value. Perfectly match with DYS BE1104 KV4000 brushless motors and DYS
3020 Props.
Item Name: DYS XM10A Mini ESC
Input voltage: 1-3s Lipo
BEC: NO
Size (L*W*H): 23*12*4.5 (mm)
Weight: 7.2g
Model: mini 10A ESC with BLheli bootloader and BLheli 14.0
Signal frequency: 20-500Hz/ Oneshot125 Ultra high speed
Firmware:BLHeli

Feature:
- XM
series esc is an upgraded version from SN series, the basic frequency
up to 50MHz and processing capacity is faster to support high KV motor
properly by using the advanced processor.
- Specially for Multi-copter, fast throttle respond;
- Suitable for throttle, which can compatible well with motor;
- Throttle
signal is twisted pair cable, reduce the crosstalk while the signal
transfer by the copper wire and flight more stable;
- Use new process ultra-low resistance MOSFET with miniaturization, and all flashes are N MOS with high withstanding current;
- Minaturization design, XM10A/20A with high performance capacitor fliter on the board,
- weight reduce to 2g, also already thicken the PCB copper specially and low heat for small aircraft.
- Support
high frequency maximum up to 500Hz throttle signal, compatible with all
flight controls; Support ultra-high frequency Oneshot125 and high PWM
frequency up to 3000Hz, flight response will be more sensitive and
rapid, throttle liner will be better and shooting will be more smooth.
It is the first choice for multicopter and racing.
- Throttle
lever travel and other settings are available to be set by USB linker;
Support two-way mode and 3D mode for racing frame.
Specs:The RS90 is a 90mm
brushless fpv quad designed to be the ultimate indoor/proximity flyer.
Full propeller protection and a tiny form factor (4” x 6” flying size)
turn any location into an fpv playground without having to worry about
leaving prop marks everywhere. Despite a slightly heavier flying weight
compared to the typical quadcopter in this size class, brushless power
produces around 60g(@8.0V) thrust for a total thrust to weight ratio of
3.5!
-full prop guards mean you’ll almost never break props, saving money and time from balancing/drilling new props
-pusher props with essentially zero obstruction downstream for higher
efficiency and a much smaller chance of props flying off as they lose
grip on the motor shaft
-narrow
as possible motor to motor width (dimension orthogonal to the quads
forward direction of travel) to fly through the tightest gaps
-motors are completely surrounded by the frame, making it impossible for them to take a direct hit
-plastic (currently nylon) is soft and flexible making it less likely to damage surroundings, which is more important indoors
-no
electronics permanently attached to outer frame so rebuilds won’t
require any soldering, just a screwdriver and about 5 minutes
-frame rear weight bias to balance out the relatively large camera platform in front and potential hd camera
-motors mounts pushed outside of the frame to allow the use of lower
profile 12mm standoffs (originally used 18mm which requires a f/f and
m/f standoff) while still maintaining decent ground clearance
-integrated battery mount which provides support in the horizontal plane, preventing battery vibrations in flight
-slightly undersized motor screw holes for a sort of integrated nyloc. I
found that screws would vibrate loose with correctly sized holes
Need a Custom RS90 Case (Links below):
