Phoenix Flight Gear
Transporter 725mm
Spyder Quad Solderless RTF Kit
** Just add your Flight Controller Choice and
Labor Charge from drop-downs above **
RTF kit:
We set out to design a transportable
Spyder frame knew that transportability had to be taken into account
along with, reliability and ease of operation being key aspects we also
had to integrate. After the 725mm Spyder Quad frame meet our demands we
started looking for the right components that would provide reliable and
efficient lift and power. Distribution of power is taken care of with
all 4 ESC's pre-soldered to a power distribution board from VOLTair. Two
JST connectors are also pre-soldered to the distribution board to
provide power to electronic accessories and your flight controller.
We chose to power the quad/X8 with motors manufactured by Avroto just
for us here at Performance Flight Gear, the PFG Edition M2814P-11s
770kv, specifically manufactured to our specifications. To feed those
PFG edition motors power, Maytech 30a OPTO ESC's flashed with Simon K
multirotor firmware provide efficient, quiet and reliable power. To
simplify the build process, the motor to ESC connections are made with
3.5mm bullet connectors and color coded wires. APC's 10x5.5 composite
propellers will provide all the lift required to get your drone flying
high in the sky. Phoenix Flight Gear, created and manufactured by pilots
for pilots.
 |
 |
All our Phoenix Flight Gear frames are 3K twill weave carbon fiber. We DO NOT USE low quality fiberglass composite sandwiched between 2 THIN LAYERS of carbon fiber!
Frame:
This Spyder
Quad frame was designed to be highly transportable with all four arms
able to swing back to fold. The frame plates are CNC cut from 1.5mm
carbon fiber and are designed to contain all of your electronics
internally. Light weight powder coated aluminum arms with 2mm CF vented
motor plates keep your motors secure and cool keeping your drone in the
air with heavy payloads. When the propellers are removed the whole frame
can fold and fit into a hard side case making travel to and from flight
locations easy.
Keeping all of
the electronics internally mounted makes the frame build neat and
clean. The frame was designed around the electronics, inside the frame
there are mounting locations for your power distribution, 4 ESC's and,
flight controller components. Venting holes help keep the ESC's cool and
improves the airflow through the interior of the frame as well.
Containing the flight electronics internally provides a massive area on
the top or bottom to mount accessories like, gimbals, FPV, downlinks or
anything else you can think of. We have also provided two mounting
locations for the DJI Zenmuse H3-2D. One centers the gimbal on the frame
and the other keeping the lens in the center of the craft. The goal is
to keep your build clean and functional keeping ease of use a key design
aspect.
The included
landing gear allows 135mm clearance below your frame. If you need more
clearance below your quad to mount larger gimbals or equipment then you
can equip the frame with the optional CarbonGear 200mm Carbon Fiber
Landing Gear. The taller landing gear combined with the CarbonGear 7mm
Rail Mount will allow you to mount an AV130, rail mount brushless
gimbal, rail mount accessory / battery plate or any other accessory that
has a 80mm width, 7mm rail mount. (taller landing gear and rail mount
sold separately)
Construction
of your air frame is straight forward and easy to understand. There are
no: glues, epoxies or resins; no complicated specialty hardware that is
hard to find and replace, no overly complicated installation of
electronics or searching for a place to mount items. Simple CAD drawings
depict the basic construction of the air frame. CAD diagrams show the
recommended installation of the electronics. American style fasteners
simplify the build using three tools, a 1/16" hex, 5/65" hex and, 5/64
nut driver.
**Frame does NOT ship assembled**

**Frame does NOT ship assembled**

**Frame does NOT ship assembled**

**Frame does NOT ship assembled**

Frame components:
- 2 - 10" lightweight aluminum rear red arms
- 2 - 10" lightweight aluminum front black arms
- 2 - CF frame plates (one top, one bottom)
- 8 - CF motor plates
- 8 - CF arm reinforcement plates
- 8 - CF legs
Included hardware:
- 52 - 4-40x1/4" Screws
- 20 - 6-32x1/12" Screws
- 22 - 1" Threaded standoffs
- 4 - 1/2" Threaded standoffs
- 4 - LG 1/2" Threaded standoffs
- 20 - 6-32 Locknuts
- 4 – Rubber grommets
Simple CAD drawings depict
the basic construction of the air frame. CAD diagrams show the
recommended installation of the electronics. American sized fasteners
simplify the build using three tools, a 1/16" hex, 5/65" hex and, 5/64
nut driver.

VoltAir® micro 60 amp power distribution board
The VOLTair
power distribution board has proven to be an extremely reliable
performer for us here at Phoenix Flight Gear. 12 ESC wire mounting
locations, four super thick gold plated copper conduction rings and 192
bias to transfer power efficiently and evenly. The numerous bias and
super thick conductors keep all of your electronics supplied with plenty
of power.
VoltAir®
micro 60 amp power distribution board - a small 50mmx50mm PCB -
which makes it very easy to wire together up to 8 ESCs and addition
power outlets for FPV and LEDs. Virtually indespensible with six
engine multicopters or Quads need several FPV and LED power outlets.
Features:
Rated and tested to 60 amps continuous - tested to 72amps for 15 secs
tiny 50x50mm - with standard 45mm
holes - (measured square axis across) - 1.6mm RoHS gold plated PCB
4 Super thick 140um copper rings
joined by 192 vias - so both sides of the board act together to
conduct large amounts of current
Plated holes for strength and 100% power delivery
11 sets of 2.0mm holes (22 in all) for ESC and power out
1 set of 2.5mm -> Power IN holes
12 additional sets of 1.5mm holes for small devices - FPV and LED
4 x M3 mounting holes unplated to isolate
5 x M3 holes in the centre for wire routing
Phoenix Flight Gear Edition Avroto M2814P 770kv
Brushless Motors

|
|
The
Phoenix Flight Gear Edition Avroto motor is a high quality, smooth
running, durable brushless motor built for multirotor UAV
applications. The custom assembly methods, reinforcements, and
components unique to Avroto motors help to provide the reliability
required for a dependable aerial platform.
Manufacturer Data:
Model number M2814P-11S
Weight approximately 100 grams not including wires.
External Dimensions 35mm D x 36mm L
Stator Dimensions 28mm D x 14mm L
Internal Shaft diameter 4mm
Prop Adapter diameter 6mm
No-load speed: 770 rpm / V
Ri (Internal Resistance) 100
Io (no load current) 0.5A
Voltage for Io measuremen 10V
Current capacity 25A/180s
Watts: 350
Lipo cell 3-4
Wire length 450mm
14magnets 12 stator arms 12N 14P
Shaft secured by snap ring
.2mm NdFeB sheet
Hardened shaft from Japan
Quality EZO brand bearings from Japan
High quality accessories included:
Includes radial mount set with prop adapter. Wire color may vary
Dimensions:
Test results from sample M2814P-11 motors courtesy of RCG member 13brv3
Avroto M2814P-11
Prop APC 10x4.7 SF APC 11x4.7 SF APC 12x3.8 SF
Max Watts @ 11.1V 122 163 201
Max Thrust Oz 30.4 39.3 46.3
Prop APC 10x4.7 SF APC 11x4.7 SF APC 12x3.8 SF
Max Watts @ 14.8V 266 346 423
Max Thrust Oz 50.9 60 60.3
Our new Phoenix
Flight Gear Edition Avroto motors have 3.5mm bullet connectors factory
installed to match up perfect with the included 30A Maytech ESC with
factory flasked SimonK FW for multirotors.
Maytech MT30A-OPTO-MK 30 Amp ESC w/SimonK w/Bullet connectors installed
**Factory Flashed w/SimonK Firmware For Multirotors**

|
MT30A-OPTO-MK ESC
is specially designed for multi-rotor copters. The ESCs are loaded
with dedicated optimized software, for extremely high performance on
MultiCopters. It will increase the handling and stability of
multirotor greatly.
Main Features:
- Handle fast refresh rates. ESCs operate with over 450Hz refresh rate.
- ESC firmware is optimized for quadcopters / multicopters.
- Excellent
Reliability. Our distributors worldwide give us feedback that our
ESCs have the best reliability rate with their customers of any brand
of ESCs they have ever sold.
Application: RC Multirotor
Cont.Current: 30A
Lipo: 2-4Cells
Burst Current(10sec): 40A
NiMh: 5-12Cells
Net Weight: 27g
BEC: N/A N/A
PCB Size(mm)(L x W x H): 56x25x8
Programe Device: Transmitter
We had 3.5mm bullet connectors factory installed to match our new Avroto Phoenix Flight Gear Edition Motors.
|
APC Propeller: 10" x 5.5" Left & Right Rotation

Description:
Hub Diameter: 0.65 in. Hub Diameter
Hub Thickness: 0.35 in. Hub Thickness
Shaft Diameter: 1/4 in. Engine Shaft Dia.
Propeller Weight: 0.53 oz.
Included are the matching Prop Spacers
This ARF Kit includes:
- (1) Phoenix Flight Gear
Transporter 725mm Spyder Quad Solderless ARF Kit
- (1) VoltAir® micro 60 amp power distribution board
- (4) Phoenix Flight Gear Edition Avroto M2814P 770kv Brushless Motors
- (4) Maytech MT30A-OPTO-MK 30 Amp ESCs w/SimonK with 3.5mm Bullet Connectors installed
- (4) APC Propellers w/adapter rings- 10" x 5.5" Left & Right Rotation
Manufactured by Phoenix Flight Gear
"Created and manufactured by pilots for pilots"
