Phoenix Flight Gear Double Decker 120mm Carbon Fiber
FPV Bind-N-Fly Blade Nano Quadcopter Extreme Edition
**Camera Not Included**
**Camera Not Included**
This Bind-N-Fly kit includes the following:
Phoenix Flight Gear Double Decker 120mm
Carbon Fiber FPV Quadcopter Drone Frame
The
micro frame market has taken off with a revolution in flight
controllers and a variety of coreless motors. This lightweight FPV frame
has a top plate that secures your micro motors and also strengthens the
frame. Securing the motors with two points also makes this one of the
most rigid frames that we have to offer to date. Build able with 8.5mm
motors you will be able to upgrade and reconfigure as your skills
improve. With minimal nylon hardware and grommet motor mounting we keep
this frame light and easy to assemble.
Another
reason we chose a two plate frame design was to strengthen the frame
and to make it more rigid. The rigid 2 plate design will also protect
your flight controller, motors, and FPV cam which fits in between the
top and bottom frame plates.
Made from 3K Twill Weave High Gloss Carbon Fiber for strength and lightweight.
Top plate is .5mm carbon fiber and the bottom plate is .8mm carbon fiber.
Frame Includes:
(4) Grommets
(8) Standoffs
(16) 2x6 Nylon Screws
FC Double sided foam tape
Fishing Line
Bumper Foam
Weight:
CL-0820-15 Hyper Speed Coreless Motor 8.5x20mm
To fit these motors into your Alias, you will have cut off and use the plugs from your old motors.
Performance data:
- operating voltage: 1.5-3.7V
- max. thrust: 40g (direct drive, Hubsan X4 propeller)
- 2.75A max. load current at 3.7V (Hubsan X4 propeller)
- factory lifetime rating: 5-6 hours
Dimensions:
- can diameter: 8.5mm
- can length: 20mm
- shaft diameter: 1mm
- shaft length: 5mm
- weight: 4.9g
All motor packs contain equal amounts of clockwise and counter
clockwise motors. To maximise performance and life span, dont run them
in reverse!
Motor rotation and correct polarity is indicated by the wire color:
clockwise: red +, blue -
counter clockwise: white +, black
Hubsan Rotor for H107L Black & White - Props
Hubsan X4 H107 Propeller Blades Props Rotor Set Factory Units H107L H107D H107C
Includes:
2 Black Propellers
2 White Propellers
4-in-1 Control Unit Rx/ESCs/Gyro
Blade Nano QX FPV Flight
Controller w/JST Battery Connector
**Now you can build your own PFG brushed micro quadcopter w/Blade Nano QX FPV FC without soldering**
We
take a stock Blade Nano QX FPV flight controller and remove the small
stock battery connector and solder a JST battery connector w/20awg
wire direct to the FC.
We leave the stock Spektrum FPV cam plug on the FC.
**This is the ONLY way you can run 8.5mm motors on a Blade Nano QX FPV flight controller**We recommend our 750mAh lipo for this setup: CLICK HERE
Required for flight:
**Micro Motor Tips**
1-Drill props with #62 drill bit so they press on all the way.
2-Rest motor bottom end cap on corner of a table or something to keep it from popping off when you push the props on.
3-Add a little epoxy to the edges of the bottom end caps to keep them from popping off in a crash or when pushing props on.
4-Let motors cool a little in between battery packs.
5-Replace nicked or damaged props as damaged props will cause the motor to run hotter and will affect efficiency.
6-Make sure micro is balanced as an unbalanced micro will not fly as well and motors will run hotter and will affect efficiency.
7-Buy spares because if you crash a lot you will need them.
Manufactured by Phoenix Flight Gear
"Created and manufactured by pilots for pilots"
