Phoenix Flight Gear Custom Built 135mm Micro-H 8mm
Motor Nano Copter Bind-n-Fly Extreme Edition
For this Extreme Edition we direct solder a JST to the FC
That's the only way to run 8mm motors
For smoothest throttle response do not upgrade to the dark Edition.
They are for "Balls to the Wall" sport flying and might not be the
best choice for FPV racing unless it is a large course.
The
micro frame market has taken off with a revolution in flight
controllers and a variety of coreless motors. This super light racing
frame has a second top plate that secures your micro motors the top and
bottom the motors strengthening the frame. Securing the motors with two
points also makes this the most rigid frame that we have to offer to
date. Build able with either 7 or 8mm motors you will be able to upgrade
and reconfigure as your skills improve. With minimal nylon hardware and
foam motor mounting we keep this frame light and easy to assemble.
For
the racer in you, the top plate can be shifted forward with 7mm motors
installed for face paced racing. Another reason we chose a two plate
frame was to strengthen the frame to make it more rigid. To protect
your flight controller we have also made two optional flight controller
yards, one for the AlienWii and one for the blade NanoQX and Hubsan X4.
If you are flying FPV we also have mounting place for an antenna
protector post for the Spectrum VA1100. There is also a ledge for
mounting the VA1100 and micro pico cameras on the front.
Frame:
The frame is cut from solid carbon fiber with 3k twill weave and a high
gloss finish. This frame was designed to be as minimalist as possible of
the best in flight times and agility. Our choice of rubber motor mounts
was for a couple of reasons, eliminates any extra hardware, keep the
frame light and easy to build. Another great benefit of the rubber motor
mounts is that they will absorb vibration from the micro motors and
propellers.
Building this micro as a micro FPV drone is also a possibility.
With a micro camera / TX unit mounted you can take this micro quad just
about anywhere. Purchase the top mounting accessory plate (sold
separately) to give your micro quad a finish look or if you need more
space to mount a micro TX unit etc. Small enough to fly indoors and
powerful enough to fly outdoors in a light breeze. Flight times are
around 7 min depending on your build specifics.
Building this micro quad could not be easier,
the motors slip into the motor mounts, the AlienWii mounts to the
center of the frame with adhesive tape. Bind and attach a DSM2
compatible satellite receiver and you’ll be ready to fly. The default
flight settings for the AlienWii will get you in the air and flying
without connecting to a computer, uploading firmware or dealing with
complicated PID settings. Should you want to do some additional tuning
of the flight controller, programing is done through Arduino and the
MultiwiiConf utility.
CL-0820-15 Hyper Speed Coreless Motor 8.5x20mm
To fit these motors into your Alias, you will have cut off and use the plugs from your old motors.
Performance data:
- operating voltage: 1.5-3.7V
- max. thrust: 40g (direct drive, Hubsan X4 propeller)
- 2.75A max. load current at 3.7V (Hubsan X4 propeller)
- factory lifetime rating: 5-6 hours
Dimensions:
- can diameter: 8.5mm
- can length: 20mm
- shaft diameter: 1mm
- shaft length: 5mm
- weight: 4.9g
All motor packs contain equal amounts of clockwise and counter
clockwise motors. To maximise performance and life span, dont run them
in reverse!
Motor rotation and correct polarity is indicated by the wire color:
clockwise: red +, blue -
counter clockwise: white +, black
Hubsan Rotor for H107L Black & White - Props
Hubsan X4 H107 Propeller Blades Props Rotor Set Factory Units H107L H107D H107C
Includes:2 Black Propellers
2 White Propellers
4-in-1 Control Unit Rx/ESCs/Gyro: Nano QX FPV
Battery (200-500mah)Radio system
Included:
Top Frame Plate
Bottom Frame Plate
2 - M3x15 nylon standoffs
4 - M3x6 nylon screws
4 - CL-0720-12 - coreless motor set, 7x20mm (2 CCW - 2 CW)
4 - Props HUBSAN Rotor for H107L 2Black & 2White
1 - BLADE 4-in-1 Flight Control Unit Rx/ESCs/Gyro (Nano QX FPV style)
Adhesive velcro
Adhesive foam 3M tape
Fish line
Frame weight: 10g
**Micro Motor Tips**
1-Drill props with #62 drill bit so they press on all the way.
2-Rest motor bottom end cap on corner of a table or something to keep it from popping off when you push the props on.
3-Add a little epoxy to the edges of the bottom end caps to keep them from popping off in a crash or when pushing props on.
4-Let motors cool a little in between battery packs.
5-Replace nicked or damaged props as damaged props will cause the motor to run hotter and will affect efficiency.
6-Make sure micro is balanced as an unbalanced micro will not fly as well and motors will run hotter and will affect efficiency.
7-Buy spares because if you crash a lot you will need them.
Accessories:

Manufactured by Phoenix Flight Gear
"Created and manufactured by pilots for pilots"