Phoenix Flight Gear CarbonSpyder 470mm
Foldable FPV Quadcopter RTF
**Custom Built and Completed in 1 week or Less!**
Optional Accessories listed at the bottom of this page.
Click arrow links to be directed to the description pages for each item!

Below are sample pics of the 470mm FPV Quadcopter RTF with Optional Accessories (GoPro Hero NOT INCLUDED)
**Kit will NOT INCLUDE EVERYTHING seen in this photo unless you add it to your cart on checkout!**
  



**Below
pics show placement of the Gimbal mounting accessory plate and the
board camera mounting plate which are optional accessories you may add
to your order** 
DJI 2212 Motor 920kv

Motor Specs:
DJI 2212/920KV
Dimension : 28X24mm
Rating : 920kv
Battery :3S,4S Shaft : 8.0mm
Weight : 56gr (with Prop Adapter)
Standard Current : 15-25A Max Current : 30A
Recommended prop : Li-Poly (11.1V) : 10×4.5 Li-Poly (14.7V) : 8X4.5
Weight: 2.2 lbs
Dimensions: 7 x 5 x 1.25 in
DJI Innovations 30 Amp Multi-Rotor Brushless ESC
This is the DJI Innovations 30 Amp Replacement Multi-Rotor Brushless ESC. This is a replacement for the DJI Flame Wheel F450 Quadcopter and F550 Hexacopter.
Specifications:
Current: 30A OPTO
Signal Frequency: 30Hz ~ 450Hz
Battery: 3S ~ 4S LiPo
DJI 1038 10" Props

More efficient: speed efficiency has been improved by more than 10%.
Optimized material structure: less stress concentration, now produced using ultra high strength material to give longevity using high speeds.
Small moment of inertia: the same weight of propeller has a smaller moment of inertia, which makes it more suitable for multi-rotors.
Phoenix Flight Gear CarbonSpyder 470mm FPV Quadcopter RTF description:
Lighter than the competition, the 1.5mm carbon fiber components and hardware weigh in at 155g. 4 DJI arms add 215g bringing the frame weight to 370g. One of our key design aspects that we incorperate to all Phoenix Flight Gear frames, folding arms and transportability. Multiple flight controller options are accommodated for you. Slots located at the center of gravity allow you to mount many flight controllers using mounting holes from 30x30 to 50x50. NAZA-M locators help center your DJI flight controller. Mounting holes for the tried and true multicopterPilot VOLTair power distribution board are on the base plate to feed your motors plenty of power and, there is also accommodation for the DJI E300 propulsion system distribution board.
For the ultimate in AP/FPV footage, we have designed a gimbal mounting plate that will give you the best AP footage you can capture, gone are the days of the hard mounted GoPro on your FPV frame that make viewers nauseous when viewing your footage. The plate is made to accommodate the DJI ZenMuse H3-2D, PhantoMounts X2 wide gimbals and many more gimbals that use the DJI Phantoms standard camera mounting holes (40mm spacing). If you plan on fast aggressive flight we recommend using the PhantoMounts X2 gimbal, because it is servo driven you will not have to worry about the "protection mode" enabling during hard fast maneuvers then require landing to re-stabilize the brushless gimbal.
A weather resistant hard case is also available, take your CarbonSpyder, transmitter, batteries and FPV goggles all to the field in only one case.
Tools / Build Supplies:
2mm hex driver
1.5mm hex driver
Low strength screw glue
Misc build supplies; servo tape, zip ties, etc…
Frame and hardware:
1.5mm CarbonSpyder Quad frame plates
4 - Black DJI Flamewheel arms
24 - M2.5x6 screws
6 - 37mm threaded standoffs
12 - M3x6 screws
4 - M3x12 screws
4 - 1/4" nylon standoffs
4 - M3 locknuts OPTIONAL ACCESSORY DESCRIPTION PAGE LINKS CLICK BELOW: 
Manufactured by Phoenix Flight Gear
"Created and manufactured by pilots for pilots"
|