| Description |
Phoenix Flight Gear CarbonSpyder 330mm FPV Quad Ready to Fly Kit **BUILT / READY TO FLY**
**Pics below show (OPTIONAL Mounting Accessory, Sparky Flight Controller, Maytech ESCs, GoPro Hero 3, Zenmuse GCU) These are NOT INCLUDED with this kit**
Description:
This frame designed for FPV flight and great transportability without sacrificing performance or agility. The two frame plates that for the body of the frame are made out of solid 1.5mm carbon fiber that has a 3k twill weave and a high gloss finish. Arms are also cut from the same solid carbon fiber in 3mm to keep down frame weight and provide a easily replaced arm in case of a crash. The solid carbon fiber frame keeps the frame strong and light weight, with the high gloss finish you will be the envy of your friends at the flight field.
Use of the single piece arms makes for a much simpler build not requiring all of the additional hardware and pieces associated with motor mount plates and multi piece arms. In the even of a damaged arm, two screws hold the arm to the frame, four screws hold your motor, remove them swap the arm with a spare (sold separately) and get back in the air, not back to the workbench.
The CarbonSpyder 330mm FPV Quad has been designed and outfitted with a variety of build types. Intended to satisfy the growing hobby of multi rotor flight and arial photography, this quad is simple to build and fly for the beginner who is looking for a economical entry to multirotors. With consideration to developing your skills, you can upgrade, tune and customize the CarbonQuad to your liking. Upgrade with high efficiency motors, propellers, FPV equipment and gimbals or, the addition of flight controller accessories as you hone your skills. The frame has been designed to be easy to build with minimal hardware and a simple layout.
Balancing your drone is crucial for quality flight. The CarbonQuad 330 is easy to balance, even with all the FPV gear you need attached. Several build configurations allow you to use this quad as a sport/leisure craft, several camera mounting options also allows you to film your fight. If you want to fly FPV then you are able to mount your camera on the included board camera mounting plate. A top mounted accessory plate help to secure and protect your FPV video downlink and battery. Should you want to take some stabilized arial footage, the CarbonGear CarbonQuad 330/470 Gimbal Mount Plate will allow you to mount a ZenMuse H3-3D gimbal. Combine that with the Gimbal Plate Board Mount Kit and you can fly FPV and get great stabilized arial footage. DJI Naza-M V2 Flight Controller
**Includes Flight Controller, PMU and GPS**
All-in-one Design
DJI adheres to
continuous innovating and improving, with the new firmware, new attitude
stabilization algorithm and optimized hardware structure, the Naza-M V2
provides better flight performance. The innovative All-in-one design
simplifies installation and saves space and weight. It contains inner
damping, controllers, 3-axis gyroscope, 3-axis accelerometer and
barometer in its light and small Main Controller. It can measure flying
altitude, attitude and therefore can be used for autopilot/automatic
control.
Independent PMU with amazing function extension
The Naza PMU V2
has enhanced BEC functionality and provides extendable CAN BUS ports,
which can support iOSD, Zenmuse H3-2D gimbal (pitch control). Support is
also included for optional Bluetooth LED module to allow parameter
adjustment via a mobile APP (future firmware upgrade required for this
functionality)
Advanced & Improved Attitude Stabilization Algorithm
The latest fourth
generation attitude stabilization algorithm not only inherits the
outstanding flight stability of DJI products, but also provides
excellent maneuverability even without the GPS module. It is more
flexible and stable, and gives the hobbyists a wonderful flight
experience. New features have been included such GPS course automatic
compensation, GPS & Compass sensor calibration, new take-off mode
and so on.
Nine Types of Multi-rotors Supported
Naza-M V2 now supports nine types of multi-rotor, which meets the different needs of the enthusiasts.
- Quad I, Quad X
- Hexa I, Hexa V, Hexa Y, Hexa IY
- Octo X, Octo I, Octo V
(Naza-M
V2 does not support the aircraft which has large vibration, so when you
choose to use hexa-rotor or octo-rotor, please pay attention to the
vibration situation and try to do some vibration dampening)
Multiple Flight Control Modes/Intelligent Switching
It offers three
types of control modes: GPS Atti. Mode (with GPS module), Atti. Mode,
Manual Mode. The pilot can switch between the three modes to achieve
different flight characteristics. It also can adjust automatically
within the flight environment and intelligently switch between GPS Atti.
Mode and Atti. Mode to make sure the flight is safe and secure. In the
software at the position of the manual mode you can choose manual,
attitude or failsafe; it supports one key failsafe trigger.
GPS Module Available/Accurate Position Hold
The plug and play
GPS module will greatly enhance the performance for Aerial Photography
with accurate Position Hold, Return-To-Home and Intelligent Orientation
Control functionalities. With the GPS Module, the multi-rotor will have
position and altitude locked accurately even in windy conditions.
Hovering accuracy is approximately 2.5m horizontal and 0.8m vertical.
Enhanced Failsafe Mode
If your transmitter
supports failsafe, then you can set failsafe through port-U. Naza
controller has built-in auto level failsafe function, which means when
the communication between MC and the transmitter is disconnected, the
outputs of all command sticks from controller will go to center
position. If the GPS module is used, you can also set RTH on failsafe.
If your transmitter has only 4 channels, then MC will work in Atti. Mode
by default without the failsafe function.
Two Levels of Low Voltage Protections
In order to prevent
your multi-rotor from crashing or other harmful consequences caused by
low battery voltage, we have designed two levels of low voltage
protection. You can choose not to use this, however we strongly
recommend you to enable the protection. Both levels of protection have
LED warning as default. The first level will blink the red light
continuously; the second level will blink red light continuously and the
multi-rotor will descend and land. In manual mode when low voltage
protection is triggered the LED warning will be active only.
Motor Arm and Motor Dis-arm
There are four ways to start the motors, see the following picture:
When
you want to start the multi-rotor, you need to perform any of the ways
of CSC. During the flight, if the motors stop, you can immediately
execute the CSC and the motors will start. This enhances the safety of
the multi-rotor; no uncontrolled starting of the motors. Motor
Disarm: There are two modes of Motor Disarm: namely Intelligent Mode and
Immediate Mode. For more information, please refer to the user manual
or DJI Wiki. Note: It has a brand new, smoother take-off
algorithm, which is more stable and provides a brand-new experience and
supports double spring TX; every time you let go of the throttle stick
it will hover.
PPM, S-BUS & Ordinary Receiver Supported
Minimum Four channel
receiver supported, also PPM and Futaba S-Bus receiver supported. PPM
& S-Bus receivers (the general use of the first 8 channels of S-Bus
receiver) to optimize the channel connection, the A, E, T, R, U
five-channel functions are set using channel X2, use only one servo
cable to connect the PPM or S-Bus to X2, this makes installation quick
and easy, not easy to make mistakes.
Independent LED Module
The Independent LED
module makes the indication of the flight status and the system status
to the ground much clearer. The pilot can get information more quickly
and more conveniently, even at night, he/she can get real-time flight
information feedback through the LED flashing frequency and colour. In
addition, the module has a USB interface, which is used for parameter
settings and firmware upgrade.
Built-in Gimbal Stabilization Function
The gimbal
stabilization module is compatible with almost all 2-axis gimbal
systems. The system will adjust the gimbal and camera according to the
attitude of the aircraft after setting the parameters the first time.
Multi-rotor One-power Output Fail Protection
In most conditions,
the whole multi-rotor will retain good attitude and rotate around the
frame arm with no power output, due to imbalanced mechanical structure
and external environment. Rotating is mainly caused by payload and
external environment. Payload heavier, rotating speed is faster. On
rotating, the hexa-rotor physical structure causes rudder out of
control. This humanistic protection function from Naza-M V2, in Attitude
or GPS Mode, makes attitude still under control even with any one power
output failed and highly reduces crash risk.
Remote Gain Adjustment
The default parameter
settings are OK for you to achieve a normal flight, and it also
supports remote parameter adjustment by using a control slider on the TX
during flight, in order to obtain better performance.
New Assistant Software & Firmware Online Update
The user interface of
the assistant software has been comprehensively updated and brings you a
new interaction experience, and instructions will automatically appear
which is very convenient. In addition, on the left side of each menu
section there is additional information. The logical design makes your
parameter settings more simple and convenient. Like other DJI products
the Naza-M V2 firmware can be upgraded free online.
| Basic Performance |
Supported Multi-rotor |
Supported ESC output |
Recommended Transmitter |
Working Voltage Range |
Quad-rotor I4, X4
Hex-rotor I6, X6, IY6, Y6
Octo-rotor I8，V8，X8 |
400Hz refresh frequency |
PCM or 2.4GHz with minimum 4 channels |
MC:4.8V~5.5V
VU Input: 7.4V ~ 26.0 V
(recommend 2S ~ 6S LiPo)
Output(V-SEN port red wire): 3A@5V
(burst current:7.5A) |
| Power Consumption |
Operating Temperature |
Assistant Software System Requirement |
|
MAX: 3.15W([email protected])
Normal:1.638W([email protected]) |
-10°C ~ 50°C |
Windows XP sp3 / Windows 7 / Windows 8 |
|
| Flight Performance |
Hovering Accuracy
(GPS Mode) |
Max Yaw Angular Velocity |
Max Tilt Angle |
Ascent / Descent |
Vertical:±0.8m
Horizontal:±2.5m |
200°/s |
35° |
6m/s，4.5m/s |
| Hardware |
Weight |
Dimensions |
Built-In Functions |
|
MC:27g
PMU:28g
GPS:27g
LED:13g |
MC: 45.5mm x 32.5mm x 18.5mm
PMU: 39.5mm x 27.5mm x 10.0mm
GPS & Compass 46mm(diameter)x10mm
LED: 25mm x 25mm x 7.0mm |
Multiple Autopilot Control Mode
Enhanced Fail-safe
Low Voltage Protection
S-Bus Receiver Support
PPM Receiver Support
Independent PMU Module
2-axle Gimbal Support |
DJI 2212 920kv Naza Motors (4)
Specifics:- DJI 2212/920KV
- Dimension : 28X24mm
- Rating : 920kv
- Battery : 3S,4S
- Shaft : 8.0mm
- Weight : 56gr (with Prop Adapter)
- Standard Current : 15-25A
- Max Current : 30A
- Recommended prop : Li-Poly (11.1V) : 10x4.5 Li-Poly (14.7V) : 8X4.5
- Gold connector is included
DJI Innovations E300 15A Electronic Speed Control (ESC)
DJI
E300 15 Amp ESC. Replacement ESC for DJI's E300 Tuned Propulsion
System. Will work with other multi-rotor setups requiring 15A ESC.
DJI 8" Propellers
(2-Left Rotation and 2 Right Rotation) 8"x4.5 Props for DJI
Flamewheel, includes 2 pair of normal and reverse props (4 props total).
We strive to find the best prop for the money and I think we found
them. These props are well balanced right out of the bag. Required for build:Battery 3s 2500, 4s 2200
Minimum 6 channel radio system
Kit comes with: - 1 - Phoenix Flight Gear CarbonSpyder 330mm FPV Quad Frame Kit
- 4 - Dji 2212 920kv motors
- 4 - Dji 8x4.5 props
- 1 - DJI NAZA V2M + GPS flight controller
- 4 - DJI E300 ESCs
- 1 - Phoenix Flight Gear 100amp Power Distribution Board
Hop-up sport build component recommendations:
RcTiger motors
Graupner 8x5 props
Sparky flight controller
30a Maytech with Simon K firmware ESC
4s 1300-4s 2200 battery
FPV rig build recommendations:
Dji 2212 920kv motors
Graupner 8x5 props
DJI V2 NAZA + GPS
18a Opto ESC
4s 2200mah battery
FatShark Predator V2 package (includes all required FPV components)
Manufactured by Phoenix Flight Gear
"Created and manufactured by pilots for pilots"
|
|
