Description:
This
new five piece 1.5mm 3k twill weave solid carbon fiber frame is based
off of our popular carbon fiber one piece carbon fiber 200QX frame. This
multi piece frame is great for the new flyer or experienced acrobatic
pilot. Should you end up crashing and breaking an arm, only two screws
hold it to the body of the frame making repair simple. Remove the broken
arm, swap your motor onto a new arm and get back in the arm in minutes
instead of having to rebuild your entire QX. We kept the frame within
the same footprint as the stock frame to utilize any cases that are
available for the stock 200QX This will fit into any of those cases with
little to no modification to the case foam. These mods allow you to
take your 200QX to the next level.
Durability was a crucial
component of the frame design. After experiencing tragic failure of the
stock Blade 200QX frame on a very early flight we first wanted to get
more aggressive in our flights and the stock frame just didn’t seem up
to the task. The motors mount to replaceable carbon fiber arms with just
a motor spacer and M7 jam nut to keep weight down. Mounting points on
the arms allow for three types of landing gear. The included standoff
landing gear or RcLogger Xtreme EyeOne landing gear, both the 38mm and
79mm landing legs will work.
Lightening of the frame was easy,
minimal hardware to secure the arms and material removed from the
central frame also improves airflow on your 4-in-1 ESC board. Reducing
the overall wind profile of the craft is another great benefit of this
frame, providing faster forward flight less affected by crosswinds.
Airflow improvements have greatly helped in our high stress acro flights
of the 200QX and turn a stock mini quad into the high performance
CarbonFiber 200QX Mini H.
Longer flights have also been made
possible through the elimination of the battery compartment allowing for
the installation of any 800-1500 2 cell batteries with a JST connector.
Battery consumption is much lower with all of the bulky plastic frame
gone, less motor power is required to perform arial maneuvers reducing
current draw on the FET’s. With the the stock canopy frame removed we
found that the ESC board runs around 50 degrees cooler, even during high
current draw sport flight.
For FPV or aerial photography buffs
out there we have made a board cam mounting plate. Screw on the top
mount accessory plate and mount your VTX up top or, use the platform off
the back of the frame to mount your electronics. With the drastic
weight reduction over the stock frame adding some lightweight FPV gear
won’t overload your quad. If you want to film your flight many of the
action cameras available will mount right under the nose and the slots
in the central frame will allow for many mounting tie points. We mounted
our Mobius under and were able to film prop free video.
For the
build process the 200QX frame splits apart and all of the internal
electronics are held and mounted with 8 #0 phillips screws and the
motors have just a acorn nut holding them in place. No soldering,
lengthening of motor wires or advanced skill is needed, the entire
process takes 45-60 minuets to complete.
This update to our one
piece 200QX frame has a couple improvements to the durability of the
frame, replaceable arms to reduce repair cost and time in the event of
arm first landing, keyed holes for the stock motors to mount and
multiple motor mounting options. Spacing on the motor holes will
accommodate a variety of motors that mount on 12-14mm spacing. Phoenix
Flight Gear recommends the Rc Tiger MT1306-10 motors paired with the 6x2
t-motor carbon prop and you’ll see your 200QX come to life with
stronger, faster, more efficient flights.
BLADE® 200 QX Bind and Fly Multicopter
Elevating Quadcopter Performance
SAFE™
(Sensor Assisted Flight Envelope) technology is a revolutionary
electronic flight envelope protection system. It also offers smoother
flight capability that battles windy conditions for you and multiple
modes so you can fly with the level of protection and assistance that
suits any given moment of the flight.
Engineered with SAFE™ Technology
Camera Mode
In
camera mode, advanced stability and small pitch and roll angle limits
combine with smooth electronic self-leveling for stable image and video
capture.
Integrated LED Lighting
High
intensity internal LED lighting provides status indication as well as
orientation. The lighting system is hidden under a translucent fuselage
and provides optimal visibility during the day and night.
Powerful Brushless Motors
The
200 QX is powered by four authoritative brushless motors which provide
intense power for aerobatics, precision flight and even heavy payloads.
Thanks to this aggressive power, the 200 QX is capable of carrying
addition weight and can be flown indoors and outdoors in medium winds.
Camera Functionality
The
Blade 200 QX has been optimized for use with the E-flite® EFC-721 HD
camera. When paired with a Spektrum transmitter this intuitive camera
can accept commands to capture quality still images and HD video during
flight.
Stability (Bailout)
White LED Status
The
Stability (Bailout) Mode is similar to Stability Mode for upright
flight. In this mode the throttle is offset to run only from 51% to
100%; this throttle curve helps prevent a pilot from accidentally flying
into the ground when flipping out of inverted flight and back to an
upright position.
3d Stagility™
Purple Status LED
3D
Stagility Mode features a self-leveling characteristic that's active
when the control sticks are released. Whether you're flying inverted or
upright, the 200 QX will self-level so you can learn inverted flight
with mild assistance. When flying in this mode, 0-50% throttle is
reversed thrust and 51%-100 is positive thrust.
3D Agility
Yellow Status LED
3D
Agility Mode was designed for experienced pilots, anyone who has
mastered inverted flight in all orientations and advanced pilots looking
for a full 3D flying experience with no self-leveling. When flying in
this mode, 0-50% throttle is reversed thrust; 51%-100 is positive
thrust.
Thanks
to its integration of SAFE technology and its powerful brushless motors
the 200 QX serves as an excellent camera platform for the E-flite
EFC-721 camera. With minimal effort, you can pair this compact HD camera
with the 200 QX and capture crisp images and HD video. Control
functions allow you to take that perfect picture at just the right
moment and to stop and start recording with the flick of a switch.
*The EFC-721 is not included with this version of the 200QX
New Firmware Update
The
firmware update for the Blade 200 QX unlocks three additional flight
modes so you can experience the aerobatic potential of the 200 QX. While
the updated firmware software is free, the Blade 200 QX update cable
(BLH7840) is required to install the software to a 200 QX. Additionally,
pilots must install the appropriate propellers prior to flight in order
to experience each flight mode to its full extent.
Download the Firmware Update Stock Specs:
| Battery:
|
800mAH, 800mAH
|
|
Completion Level:
|
Bind-N-Fly
|
|
Is Assembly Required:
|
No
|
|
Main Blade Material:
|
Plastic
|
|
Main Rotor Diameter:
|
4.45 in (113mm), 4.45 in (113mm)
|
|
Rotor Type:
|
Quad-Copter
|
|
Size/Scale:
|
200mm |
Link to Blade 200QX User Manual:http://www.horizonhobby.com/pdf/BLH7780-Manual_EN.pdf
Weights:Frame, arms and arm HW: 21.8
Included 40mm legs: 5.5g
FPV cam, plate, tab with hardware 5g
Accessory plate with hardware: 8g
Weights for comparison:
Carbon Fiber 200QX One piece frame: 17g
Carbon Fiber 200QX One piece HD frame: 22.5g
Elevating Quadcopter Performance
SAFE™
(Sensor Assisted Flight Envelope) technology is a revolutionary
electronic flight envelope protection system. It also offers smoother
flight capability that battles windy conditions for you and multiple
modes so you can fly with the level of protection and assistance that
suits any given moment of the flight.
Engineered with SAFE™ Technology
Camera Mode
In
camera mode, advanced stability and small pitch and roll angle limits
combine with smooth electronic self-leveling for stable image and video
capture.
Integrated LED Lighting
High
intensity internal LED lighting provides status indication as well as
orientation. The lighting system is hidden under a translucent fuselage
and provides optimal visibility during the day and night.
Powerful Brushless Motors
The
200 QX is powered by four authoritative brushless motors which provide
intense power for aerobatics, precision flight and even heavy payloads.
Thanks to this aggressive power, the 200 QX is capable of carrying
addition weight and can be flown indoors and outdoors in medium winds.
Camera Functionality
The
Blade 200 QX has been optimized for use with the E-flite® EFC-721 HD
camera. When paired with a Spektrum transmitter this intuitive camera
can accept commands to capture quality still images and HD video during
flight.
Stability (Bailout)
White LED Status
The
Stability (Bailout) Mode is similar to Stability Mode for upright
flight. In this mode the throttle is offset to run only from 51% to
100%; this throttle curve helps prevent a pilot from accidentally flying
into the ground when flipping out of inverted flight and back to an
upright position.
3d Stagility™
Purple Status LED
3D
Stagility Mode features a self-leveling characteristic that's active
when the control sticks are released. Whether you're flying inverted or
upright, the 200 QX will self-level so you can learn inverted flight
with mild assistance. When flying in this mode, 0-50% throttle is
reversed thrust and 51%-100 is positive thrust.
3D Agility
Yellow Status LED
3D
Agility Mode was designed for experienced pilots, anyone who has
mastered inverted flight in all orientations and advanced pilots looking
for a full 3D flying experience with no self-leveling. When flying in
this mode, 0-50% throttle is reversed thrust; 51%-100 is positive
thrust.
Thanks
to its integration of SAFE technology and its powerful brushless motors
the 200 QX serves as an excellent camera platform for the E-flite
EFC-721 camera. With minimal effort, you can pair this compact HD camera
with the 200 QX and capture crisp images and HD video. Control
functions allow you to take that perfect picture at just the right
moment and to stop and start recording with the flick of a switch.
*The EFC-721 is not included with this version of the 200QX
New Firmware Update
The
firmware update for the Blade 200 QX unlocks three additional flight
modes so you can experience the aerobatic potential of the 200 QX. While
the updated firmware software is free, the Blade 200 QX update cable
(BLH7840) is required to install the software to a 200 QX. Additionally,
pilots must install the appropriate propellers prior to flight in order
to experience each flight mode to its full extent.
Download the Firmware Update Stock Specs:
| Battery:
|
800mAH, 800mAH
|
|
Completion Level:
|
Bind-N-Fly
|
|
Is Assembly Required:
|
No
|
|
Main Blade Material:
|
Plastic
|
|
Main Rotor Diameter:
|
4.45 in (113mm), 4.45 in (113mm)
|
|
Rotor Type:
|
Quad-Copter
|
|
Size/Scale:
|
200mm |
Link to Blade 200QX User Manual:http://www.horizonhobby.com/pdf/BLH7780-Manual_EN.pdfKit Specs:ALL STOCK Blade 200QX COMPONENTS
1 - PFG 1.5mm Carbon Fiber 200QX Five Piece Mini-H Body
4 - PFG 1.5mm Carbon Fiber 200QX Five Piece Arms
4 - M3x6 screws
4 - M3x40 nylon landing leg standoffs
8 - M2x6 screws
8 - M2 locknuts
4 - M1.4x4 self tapping screws
4 - Motor mount spacers
4 - M7 Jam nuts
Adhesive Foam
Adhesive Velcro
Fish Line
Velcro strap
Requires:2.0mm allen wrench
1.3mm allen wrench
#0 Phillips head screwdriver
4mm Nut driver
Manufactured by Phoenix Flight Gear
"Created and manufactured by pilots for pilots"
