**Shown with optional flight controller**
**Flight controller choices are in checkout listing**

**Shown with optional electronics - Electronics and Props not included**

**GoPro can easily be mounted to the frame and keep props out of view.
GoPro Camera NOT INCLUDED**

**GoPro can easily be mounted to the frame and keep props out of view.
GoPro Camera NOT INCLUDED**

**Shown with (Optional) Short Landing Gear**

**Frame Shown with (Optional) Tall Landing Gear**

All our Phoenix Flight Gear frames are 3K twill weave carbon fiber. We DO NOT USE low quality fiberglass composite sandwiched between 2 THIN LAYERS of carbon fiber!
Kit Description:
Phoenix Flight Gear
has designed a great new Acro / FPV frame. The Flight Ring 328, a single
piece carbon fiber frame designed for speed and efficiency for
acrobatic flight and light FPV.
The single piece frame design has
many benefits for both the build and flight. No frame assembly required!
CNC cut from 2mm carbon fiber, the Flight Ring frame has; common
12-14mm slotted motor mounts, indicators for CG balancing, strap slots
for securing your battery and gear, NAZA-M locators, slotted flight
controller mounting for flight controllers mounting on a 30 to 45mm
square, motor wire routing, optional accessory plate and optional
landing gear. We have spent countless hours designing and test flying to
ensure that this design is easy to build, easy to fly, and durable for
you acro pilots, and most importantly, fun to fly for the novice and
experienced.
We spent lot of time on
the development of the new ring design. Aside from the load
distribution and benefits in a crash situation we put some function
into the frame design as well. We incorporated a wide center section
that runs from the front to the rear of the frame allowing you to mount
just about anything that you want to carry. With the center section
running front to rear you can hard mount your GoPro or other FPV camera
up front without props in the shot. Your video downlink can mount onto
the rear away from your electronics and mount your battery in-between to
balance your center of gravity.
The ring design has
many benefits for the acro pilot. The arms are all joined together
distributing the load across the frame. By joining the arms there is a
great improvement in rigidity and strength. This allows for a reduction
in arm flex and, provides protection against damage in a crash with the
stress distributed around the entire frame. In the event of an arm first
crash the frame will have a tendency to roll out the crash instead of
spearing into the ground and snapping an arm or damaging a motor.
Weighing in at 90
grams. The single piece 2mm thin frame minimizes the airframes wind
resistance providing high efficiency in flight. The choice of carbon
fiber as the frame material was an easy one; carbon fiber is lighter,
thinner and more rigid than glass fiber alternatives such as G10. With
this highly efficient super light carbon fiber frame you can enjoy
flights over 15 min.
Also available for
purchase is an optional accessory mounting plate. It will attach to the
frame with a few included standoffs and screws allowing you to mount
additional electronics or cover the FC system and radio system giving a
finished, classy look. The accessory mounting plate also stacks,
allowing you to mount a second plate over the first if needed, just
order a second accessory plate. A plate can be mounting to the under
side of the frame if desired to create a battery shelf or mount a FPV
transmitter. Optional landing gear is also available for purchase, short
30mm landing gear for general use and tall 60mm landing gear that will
allow enough clearance below your frame for a hard mounted GoPro camera.
RcTiger MT2206-1200kv
High Performance Brushless Motor





The Tiny T-Motor Multicopter motor 2206 KV1200 28.6grams.
5mm diameter prop holder.
100mm lead wires with 2.5mm bullet connectors attached.
Prop |
Volts(V) |
Amps(A) |
Thrust(g) |
Watts(W) |
Efficiency(g/W) |
6 X 5 |
7 |
1.7 |
109 |
11.9 |
9.16 |
8.4 |
2.3 |
150 |
19.32 |
7.76 |
10.5 |
3.2 |
223 |
33.6 |
6.64 |
11.1 |
3.4 |
250 |
37.74 |
6.62 |
7035 |
7 |
1.3 |
97 |
9.1 |
10.66 |
8.4 |
1.7 |
128 |
14.28 |
8.96 |
10.5 |
2.4 |
193 |
25.2 |
7.66 |
11.1 |
2.6 |
225 |
28.86 |
7.80 |
8 X 3.8 |
7 |
3.5 |
230 |
24.5 |
9.39 |
8.4 |
4.6 |
310 |
38.64 |
8.02 |
10.5 |
6.4 |
435 |
67.2 |
6.47 |
11.1 |
7 |
473 |
77.7 |
6.09 |
9 X 3.8 |
7 |
4.6 |
270 |
32.2 |
8.39 |
8.4 |
5.9 |
355 |
49.56 |
7.16 |
10.5 |
8 |
480 |
84 |
5.71 |
11.1 |
8.4 |
530 |
93.24 |
5.68 |
|
Rc Tiger Motor 8x2.7 T-Motor
Carbon Fiber Props (Pair)
**Super Efficient Props**

Includes:
- 2-CW Propeller
- 2-CCW Propeller
DJI Naza-M V2 w/GPS Stabilization Mode
All-in-one Design
DJI adheres to continuous innovating and improving, with the new
firmware, new attitude stabilization algorithm and optimized hardware
structure, the Naza-M V2 provides better flight performance. The
innovative All-in-one design simplifies installation and saves space
and weight. It contains inner damping, controllers, 3-axis gyroscope,
3-axis accelerometer and barometer in its light and small Main
Controller. It can measure flying altitude, attitude and therefore can
be used for autopilot/automatic control.
Independent PMU with amazing function extension
The Naza PMU V2 has enhanced BEC functionality and provides extendable
CAN BUS ports, which can support iOSD, Zenmuse H3-2D gimbal (pitch
control). Support is also included for optional Bluetooth LED module
to allow parameter adjustment via a mobile APP (future firmware
upgrade required for this functionality)
Advanced & Improved Attitude Stabilization Algorithm
The latest fourth generation attitude stabilization algorithm not only
inherits the outstanding flight stability of DJI products, but also
provides excellent maneuverability even without the GPS module. It is
more flexible and stable, and gives the hobbyists a wonderful flight
experience. New features have been included such GPS course automatic
compensation, GPS & Compass sensor calibration, new take-off mode
and so on.
Nine Types of Multi-rotors Supported
Naza-M V2 now supports nine types of multi-rotor, which meets the different needs of the enthusiasts.
- Quad I, Quad X
- Hexa I, Hexa V, Hexa Y, Hexa IY
- Octo X, Octo I, Octo V
(Naza-M V2 does not support the
aircraft which has large vibration, so when you choose to use
hexa-rotor or octo-rotor, please pay attention to the vibration
situation and try to do some vibration dampening)
Multiple Flight Control Modes/Intelligent Switching
It offers three types of control modes: GPS Atti. Mode (with GPS
module), Atti. Mode, Manual Mode. The pilot can switch between the
three modes to achieve different flight characteristics. It also can
adjust automatically within the flight environment and intelligently
switch between GPS Atti. Mode and Atti. Mode to make sure the flight
is safe and secure. In the software at the position of the manual mode
you can choose manual, attitude or failsafe; it supports one key
failsafe trigger.
GPS Module Available/Accurate Position Hold
The plug and play GPS module will greatly enhance the performance for
Aerial Photography with accurate Position Hold, Return-To-Home and
Intelligent Orientation Control functionalities. With the GPS Module,
the multi-rotor will have position and altitude locked accurately even
in windy conditions. Hovering accuracy is approximately 2.5m
horizontal and 0.8m vertical.
Intelligent Orientation Control
Usually, the forward direction of a flying multi-rotor is the same as
the nose direction. By using Intelligent Orientation Control (IOC),
wherever the nose points, the forward direction has nothing to do with
nose direction:
In course lock flying, the forward direction is the same as a recorded nose direction. See the above figures(Mode 1):
In home lock flying, the forward direction is the same as the direction
from home point to multi-rotor. See the above figures (Mode 2):
Enhanced Failsafe Mode
If your transmitter supports failsafe, then you can set failsafe
through port-U. Naza controller has built-in auto level failsafe
function, which means when the communication between MC and the
transmitter is disconnected, the outputs of all command sticks from
controller will go to center position. If the GPS module is used, you
can also set RTH on failsafe. If your transmitter has only 4 channels,
then MC will work in Atti. Mode by default without the failsafe
function.
Two Levels of Low Voltage Protections
In order to prevent your multi-rotor from crashing or other harmful
consequences caused by low battery voltage, we have designed two
levels of low voltage protection. You can choose not to use this,
however we strongly recommend you to enable the protection. Both
levels of protection have LED warning as default. The first level will
blink the red light continuously; the second level will blink red
light continuously and the multi-rotor will descend and land. In
manual mode when low voltage protection is triggered the LED warning
will be active only.
Motor Arm and Motor Dis-arm
There are four ways to start the motors, see the following picture:
When you want to start the multi-rotor,
you need to perform any of the ways of CSC. During the flight, if the
motors stop, you can immediately execute the CSC and the motors will
start. This enhances the safety of the multi-rotor; no uncontrolled
starting of the motors.
Motor Disarm: There are two modes of Motor
Disarm: namely Intelligent Mode and Immediate Mode. For more
information, please refer to the user manual or DJI Wiki.
Note: It has a brand new, smoother take-off
algorithm, which is more stable and provides a brand-new experience
and supports double spring TX; every time you let go of the throttle
stick it will hover.
PPM, S-BUS & Ordinary Receiver Supported
Minimum Four channel receiver supported, also PPM and Futaba S-Bus
receiver supported. PPM & S-Bus receivers (the general use of the
first 8 channels of S-Bus receiver) to optimize the channel
connection, the A, E, T, R, U five-channel functions are set using
channel X2, use only one servo cable to connect the PPM or S-Bus to
X2, this makes installation quick and easy, not easy to make mistakes.
Independent LED Module
The Independent LED module makes the indication of the flight status
and the system status to the ground much clearer. The pilot can get
information more quickly and more conveniently, even at night, he/she
can get real-time flight information feedback through the LED flashing
frequency and colour. In addition, the module has a USB interface,
which is used for parameter settings and firmware upgrade.
Built-in Gimbal Stabilization Function
The gimbal stabilization module is compatible with almost all 2-axis
gimbal systems. The system will adjust the gimbal and camera according
to the attitude of the aircraft after setting the parameters the
first time.
Multi-rotor One-power Output Fail Protection
In most conditions, the whole multi-rotor will retain good attitude
and rotate around the frame arm with no power output, due to
imbalanced mechanical structure and external environment. Rotating is
mainly caused by payload and external environment. Payload heavier,
rotating speed is faster. On rotating, the hexa-rotor physical
structure causes rudder out of control. This humanistic protection
function from Naza-M V2, in Attitude or GPS Mode, makes attitude still
under control even with any one power output failed and highly
reduces crash risk.
Remote Gain Adjustment
The default parameter settings are OK for you to achieve a normal
flight, and it also supports remote parameter adjustment by using a
control slider on the TX during flight, in order to obtain better
performance.
New Assistant Software & Firmware Online Update
The user interface of the assistant software has been comprehensively
updated and brings you a new interaction experience, and instructions
will automatically appear which is very convenient. In addition, on
the left side of each menu section there is additional information.
The logical design makes your parameter settings more simple and
convenient. Like other DJI products the Naza-M V2 firmware can be
upgraded free online.
Basic Performance |
Supported Multi-rotor |
Supported ESC output |
Recommended Transmitter |
Working Voltage Range |
Quad-rotor I4, X4
Hex-rotor I6, X6, IY6, Y6
Octo-rotor I8,V8,X8 |
400Hz refresh frequency |
PCM or 2.4GHz with minimum 4 channels |
MC:4.8V~5.5V
VU Input: 7.4V ~ 26.0 V
(recommend 2S ~ 6S LiPo)
Output(V-SEN port red wire): 3A@5V
(burst current:7.5A) |
Power Consumption |
Operating Temperature |
Assistant Software System Requirement |
|
MAX: 3.15W([email protected])
Normal:1.638W([email protected]) |
-10°C ~ 50°C |
Windows XP sp3 / Windows 7 / Windows 8 |
|
Flight Performance |
Hovering Accuracy
(GPS Mode) |
Max Yaw Angular Velocity |
Max Tilt Angle |
Ascent / Descent |
Vertical:±0.8m
Horizontal:±2.5m |
200°/s |
35° |
6m/s,4.5m/s |
Hardware |
Weight |
Dimensions |
Built-In Functions |
|
MC:27g
PMU:28g
GPS:27g
LED:13g |
MC: 45.5mm x 32.5mm x 18.5mm
PMU: 39.5mm x 27.5mm x 10.0mm
GPS & Compass 46mm(diameter)x10mm
LED: 25mm x 25mm x 7.0mm |
Multiple Autopilot Control Mode
Enhanced Fail-safe
Low Voltage Protection
S-Bus Receiver Support
PPM Receiver Support
Independent PMU Module
2-axle Gimbal Support |
Rc Tiger T-Motor T12A 12 amp ESC Factory
Flashed w/SimonK
**We Had ESC's Flashed w/SimonK and 2.5mm Bullets Installed At The Factory**
**They also Have JST's Factory Installed For Our Solderless ARF kits Or 6-Way JST Harness**

|
Output: Continuous 12A, Burst 15A up to 10 Secs.
Input Voltage: 2-4 cells lithium battery or 5-12 cells NiCd/NIMh battery.
BEC: Pentium-12A: 1A / 5V (Linear mode).
Max Speed: 210,000rpm for 2 Poles BLM, 70,000rpm for 6 poles BLM, 35,000rpm for 12 poles BLM.
(BLM: BrushLess Motor)
Size: 32mm (L) * 24mm (W) * 8mm (H).
Weight: 12g.
Features:
1.Extreme low output resistance, super current endurance.
2.Multiple protection features: Low-voltage cut-off
protection / over-heat protection / throttle signal loss protection.
3.3 start modes: Normal / Soft / Super-Soft, compatible with fixed-wing aircrafts and helicopters.
4.Throttle range can be configured and is fully compatible with all transmitters currently available on market.
5.Smooth, linear and precise throttle response.
6.Our pocket-sized Program Card can be purchased separately for extremely easily programming the ESC at the field.
7.With a program card, you can activate the music playing
function of the ESC, and totally there are 15 songs can be selected |
6-Way JST Harness with XT60 Connector
for 4 ESC's/2 Aux Inputs
**Use this with our new 12A T-Motor 12A ESC's w/Factory JST's Installed For a Solderless Custom Build**

Included:
(1) - PFG 328 Flight Ring Frame
(4) - Motors: RcTiger MT2206-1200kv
(4) - Propellers: Rc-Tiger 8"x2.7 Professional Carbon Fiber
(4) - ESC: Rc Tiger T12A Esc
(1) -
6-Way JST Harness with XT60 Connector