Phoenix Flight Gear 135mm Brushed Multiflite Quadcopter
w/8mm Motors BNF for 8mm Motors (MultiFlite Version)
**This micro Quadcopter comes Custom built just Bind N Fly**
Just add TX from dropdown box to make a Ready To Fly,
Will bind to ANY SPEKTRUM Transmitter
**Shown with Optional Top Plate and FPV Camera NOT INCLUDED**
**Choose from Drop Down Above to add Top Plate to cart**
**Choose from Drop Down Above for USB adapter for programming**



The micro frame
market has taken off with a revolution in flight controllers and a
variety of coreless motors. Build this hexacopter with 8mm motors. With
minimal hardware and rubber grommet motor mounting we keep this frame
light and easy to assemble.
We
designed this frame specifically for the new Multiflite Hexa/Quadcopter
flight controller but it can be used with any micro brushed hexacopter
FC.
Specs:
Size: 135mm
Phoenix Flight Gear 135mm Carbon Fiber Micro-H Frame
MultiFlite Nano-B-FC Brushed Hex Flight
Controller v1.0
**Please Note This FC Will Run A Quadcopter Or Hexacopter**

Description:
Nano
sized brushed flight controller ideal for DIY multicopters with up to 6
brushed motors. Comes pre-installed with latest CleanFlight firmware,
with tweaks and defaults made to utilize everything from this tiny
flight controller!
Features: Baseflight & Cleanflight compatible
Single side populated (for super easy mounting with double side tape)
2.9g
MPU6050 Accelerometer + Gyroscope
Baro pads (chip not populated currently)
Mag pads (chip not populated currently)
Brushed motor support up to 6 motors (all populated with Nfets)
6.3A N Channel fets
Flight battery voltage monitoring
Spektrum Satellite (3.3v) or PPM (vbatt) rx input
Spektrum bind button (hold on boot to bind)
RSSI PWM to Analog (RC circuit) on ADC5
CH2, ADC5 pads available as solder pads
3.3v Buck/Boost regulator (no brownouts) for super clean power
1S (4.2V) only (maximum input voltage 5.5v)
Expansion headers (SPI, SWDIO/SWCLK, Serial0, Serial1, CH7, CH8, 3.3V, VBAT, GND)
WS2812B LED header (including logic level converter to power LEDs direct from VBATT)
Buzzer led for low battery alarm (bright LED could also be used)
Buzzer transistor either for physical buzzer or a simple LED
Connectors all around edge and on both sides with labels
I2C pads broken out
3.3v and GND pads for auxiliary expansion
Documentation: The product user manual can be found here:
ManualIncluded Accessories |
6x 1.25mm 2pin headers (Motor Outputs),
1x 1.50mm 3pin header (Spek),
1x 1.25mm 5pin header (buzz + LED),
1x 0.1" 2pin header (LiPo in),
1x 4pin to FTDI (FTDI cable),
1x 3pin RX cable (1.50mm, tin plated terminals) |
Electrical Characteristics |
Input Voltage |
3-5v (1S LiPo) |
Output Voltage |
3.3v |
Flight Controller Features |
Board Type |
Brushed (6x integrated 6.3A N-FETs) |
Compatible Firmware |
Baseflight, Cleanflight |
Motor Outputs |
6 |
Processor Type |
STM32 |
Sensors |
MPU6050 (Acc + Gyro) |
Physical Attributes |
Length |
30mm |
Width |
30mm |
Height |
4mm |
Weight |
2.9g |
CL-0820-17 "Anodized Dark Edition"
Coreless motor set, 8.5x20mm (speed: insane), direct drive
**Comes with 4 Motors 2CW, 2CCW**
Compatible to:- Hubsan 107C, 107D
- all other micro quads with 8.5mm motor holders
Performance Data:
- Speed: 17.000K
-
Operating voltage: 1.5-3.7V
- Max. static thrust: 40g (direct drive, Hubsan X4 propeller)
- 3.2A max. load current at 3.7V (Hubsan X4 propeller)
- Factory lifetime rating: 5-6 hours
Dimensions:
- can diameter: 8.5mm
- can length: 20mm
- shaft diameter: 1mm
- shaft length: 5mm
-
weight: 4.9g
- housing: black anodised
All motor packs contain equal amounts of clockwise and counter
clockwise motors. To maximize performance and life span, don't run them
in reverse!
Motor rotation and correct polarity is indicated by the wire color:
clockwise: red +, blue -
counter clockwise: white +, black -
The new benchmark in the Micro Copter Universe!
Note: these motors do not include pinions!! For Alias Plug'n'Play motors.
This direct drive dark edition 0820-17 motor features shorter 8cm wires, and Micro-JST-1.25 plugs
**Micro Motor Tips**1-Drill props with #62 drill bit so they press on all the way.
2-Rest motor bottom end cap on corner of a table or something to keep it from popping off when you push the props on.
3-Add a little epoxy to the edges of the bottom end caps to keep them from popping off in a crash or when pushing props on.
4-Let motors cool a little in between battery packs.
5-Replace nicked or damaged props as damaged props will cause the motor to run hotter and will affect efficiency.
6-Make sure micro is balanced as an unbalanced micro will not fly as well and motors will run hotter and will affect efficiency.
7-Buy spares because if you crash a lot you will need them.
Hubsan Rotor for H107L Black & White - Props

Hubsan X4 H107 Propeller Blades Props Rotor Set Factory Units H107L H107D H107C
Includes:2 Black Propellers
2 White Propellers
Lemon Rx DSM2 Compatible Satellite Receiver
*Compatable With The Our New AlienWii Brushed Flight Controller*
Specification
Type: |
DSM2 Compatible Satellite Full Range Receiver |
Modulation: |
DSM2 Compatible |
Band: |
2.4 GHz |
Dimension: |
1.7(L) x 1.5(W) x 1(H) mm |
Weight: |
2.5 gram |
Voltage Range: |
3.3V from Receiver |
User Manual Download:Click to download Lemon Rx User Manual.pdf
Female JST to Male JST Extension Cable
**Photo below shows how/where to connect your Extension Cable**

This cable was designed for the new Multiflite
brushed Hexacopter/Quadcopter flight controller but can also be used as a
JST extension.
Optional USB TTL FTDI Adapter
**See Drop Down at top to add**

Description:
Super
simple USB TTL (FTDI) Adatpter! Takes a Mini USB connector and provides
USB-Serial communication, perfect for configuring your flight
controller! Small, light, and cheap! You just can't go wrong with this
Features:
- FTDI232 branched chip
- Voltage select jumper (NOTE: When used with nano-B-FC, if powering flight controller from battery the voltage select jumper MUST be removed)
Electrical Characteristics |
Input Voltage |
5v |
Output Voltage |
3.3-5v |
Physical Attributes |
Length |
37mm |
Width |
19mm |
Height |
11mm |
Weight |
6g |


Manufactured by Phoenix Flight Gear
"Created and manufactured by pilots for pilots"