| Description |
DJI F450 ARF NAZA Kit
Shipped Assemled, Setup, and Tested
Ready To Fly
Just add battery, Transmitter,Receiver
|
| |
|---|
|
|---|
Ultrastrength material Frame Arms adopt
PA66+30GF Ultrastrength material design, provide better crashworthiness.
Integrated PCB wiringUsing high strength
compound PCB frame board, which makes wiring of ESCs and battery more
safe and easier.
|
Huge assemble space
Optimized frame design, provides abundant assemble space for autopilot systems.
Gorgeous Frame Arms Provide different
color frame arms: red, white, black, which makes your flight more
colorful.
|
FlameWheel series is multi-rotor frame designed for
all pilots for fun or AP. With DJI WKM or NAZA autopilot system, it can
achieve hovering, cruising, even rolling and other flight elements. It
can be applied for entertainment, aerial photography, FPV and other
aeromodelling activities.
SPECIFICATIONS OF ARF:
| Model |
Frame Weight |
Diagonal Wheelbase |
Takeoff Weight |
| Flame Wheel (F450) |
282g |
450mm |
800g ~ 1600g |
| |
|
|
|
| Recommended Propeller |
Recommended Battery |
Recommended Motor |
Recommended ESC |
| 10×3.8in ; 8×4.5in |
3S~4S LiPo |
22×15mm or 22×12mm |
30A OPTO |
|
| NAZA Details: |
-
All-in-One design. All-in-One Design
integrates inner damping, controller, gyroscope, accelerometer and
barometer, which simplifies installation and saves space.
-
Advanced attitude stabilization algorithm.
Advanced mix guidance algorithm and control algorithm, inherits
outstanding flight stability of DJI products, provides excellent
maneuverability, gives hobbyists wonderful flight experience.
-
Low voltage protection. Two-level low voltage protection. low voltage LED alarm, and automatic landing.
-
D-BUS. D-Bus supports S-BUS receiver system
-
2-axis Gimbal Stabilization. The gimbal
stabilization module is compatible with almost all 2-axis gimbal
systems. The system will adjust the gimbal and camera according to the
attitude of the helicopter after setting the parameters the first time.
-
Upgradeable and extendible Easy firmware upgrade, extendible port for future use is available.
NAZA SPECIFICATIONS:
| General |
| Built-In Functions |
Autopilot |
|
Auto Level Fail-safe |
|
Low Voltage Protection |
|
S-Bus Receiver Support |
|
2-axle Gimbal Support |
| Peripheral |
|
| Supported Multi-rotor |
Quad-rotor I, X; |
|
Hex-rotor I, V. |
| Supported ESC output |
400Hz refresh frequency. |
| Recommended Transmitter |
PCM or 2.4GHz with minimum 4 channels. |
| Assistant Software System Requirement |
Windows XP SP3Windows 7 |
| Electrical &Mechanical |
|
| Working Voltage Range |
MC:4.8V~5.5V |
| |
VU: 7.2V ~ 26.0 V (recommend 2S ~ 6S LiPo) |
| Power Consumption |
MAX1. 5W ([email protected]) |
|
Normal:0.6W ([email protected]) |
| Operating Temperature |
-10C ~50C |
| Weight |
MC:25g |
| |
VU:20g |
| Dimensions |
MC: 45.5mm x 31.5mm x 18.5mm
|
|
VU: 32.2mm x 21.1mm x 7.7mm |
Flight Performance
(can be effected by mechanical performance and payloads) |
| Max Yaw Angular Velocity |
190 degrees/ s |
| Max Tilt Angle |
45 degrees |
| Ascent / Descent |
+6m/s |
|
**PLEASE READ**
When flying, the fast rotating propellers of
FlameWheel will cause serious damage and injury. Therefore, please fly
with a high safety consciousness.
Keep flying multi-rotor away from objects, such as obstacles, human beings, high-voltage lines and so on.
Do not get close to or even touch the working motors and propellers, which will cause serious injury.
Do not over load the multi-rotor.
Check whether the propellers and the motors are installed correctly and firmly before flight.
Make sure the rotation direction of each propeller is correct.
Check whether all parts of multi-rotor are in good condition before flight. Do not fly with old or broken parts.
Use DJI parts as much as possible.
|
|
